BISB42EKB General Electric Refrigerator - Instructions

Pull out the old, dump the nasty ice. Remove 4 screws attached to the front cover. throw in trash, replace with new auger assembly, with 4 screws. Put it back in ice maker and let it make ice. Easy, cheap and never left the house to searc for the right part, found it on the front porch.

Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.

i ordered this ice maker on sunday night and paid for the cheapest shipping. it got here monday morning and i couldnt believe it. super fast shipping!! works great

This is the easiest thing in the world - thanks for sharing other's installation - it took 5 mins - works perfect & we have clean ice - 4 easy screws to remove - anyone can do it!

Removed old ice bucket with auger. Unscrewed front plates that form the front of the ice bucket. Replaced the front plates on the new part (ice bucket and auger). Replaced new assemblage. It took about 20 minutes. Had to empty ice out and put in a temporary cooler for storage. Bigger problem than the repair was diagnosing what was wrong. Pushed disagnose button and it said ice maker was working normallly. Careful examination of the ice bucket removed from refrigerator showed spring out of place on long metal rod that protrudes from the back of the ice bucket and fits into a square hole in back of refrigerator. Examined other end of rod that engages with plastic parts that run the ice auger and ice crusher mechanism. A piece must have broken off. That was the problem. Refrigerator ice maker now works fine as originally designed. Push crudh the ice crusher engages and you get crused ice. Push cubes and the icemaker crusher slides out of the way and you get cubes.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP