ASI2175GRB04 Maytag Refrigerator - Instructions

As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

remove door pull gasket out put new gasket in replace door

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

Checked the water line from the wall to the supply port of the inlet valve and it was suppling water but no water beyond the water inlet valve, So I ordered a new inlet valve and installed, and it fixed the problem. Inlet valve supplies water to the ice maker and water dispenser filter housing. Partselect videos and you tube installation videos very helpful. Partselect troubleshooting guide also very helpful. Great company

I measured the part then looked for a similar switch that might work. I was so happy to find the exact part we needed for our 24 year old refridgerator!! I was so impressed with your slection of parts and best of all I had the part in 2 days! You are in my "favorites" just in case I need you again!

Thank you

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

Steps to replace Whirlpool evaporator fan motor
1. Watch numerous DIY Youtube videos
2. Move frozen food to refrigerator section, close refrigerator door
3. Cut power to refrigerator
4. Remove all shelves and bins in freezer section
5. Back panel has two parts, a top and a bottom section
6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt
7. Gently pull and work top panel out
8. Remove screw bolts from all four corners in lower panel and remove bottom panel
9. Verify power has been turned off
10. Unclip grounding wire
11. Unclip evaporator fan motor from power
12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable.
13. Remove plastic fan with firm pull
14. Unclip bottom brace to remove evaporator fan motor
15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets
16. Install new evaporator in cradle and clip-in the bottom brace
17. Install new fan blade on motor
18. Place cradle with new evaporator fan motor back in freezer
19. Reclip power and ground wire
20. Turn on power and test if working correctly
21. Turn off power
22. Complete steps from 8 to 2 in reverse

Easy repair, third time in four months, same part. I don't recommend Whirlpool refer's. Stick to the washer and dryers.

I added an icemaker kit. Everything I needed was in the kit. The refrigerator was presetup for an icemaker it was just never added. The only problem I had was that the holes for attaching the water solenoid were not pre drilled so I had to drill them myself and use sheet metal screws. The icemaker is working great.

No repair needed. Just inserted the storage bin onto the hooks provided on the inside of the door.

Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.

I removed the plastic portion to get to the switch and wires. I removed the old switch by disconnecting the two wires and pushing it out of its setting.

I discovered the old switch only had 2 prongs where the new switch had 3. Once I figured which 2 of the 3 prongs would light the lightbulb,
I then connected the two wires to the correct prongs of the new switch. I pushed the new switch into its setting and replaced the plastic portion on the refrigerator. Voila, success. The refrigerator door now comes on when its door is opened.

Thanks for the having the part and getting it at our door step in 3 days.