ARS2304AW-PARS2304AW0 Amana Refrigerator - Instructions

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

Removed the back wall (several screws) of the freezer too get at the thermostat and removed the thermostat and after checking to makes sure I plugged the wires in correctly I replaced the defrost timer by removing the housing that held it in place, which was located underneath the freezer compartment on outside of the unit. That was it!

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

I unplugged the unit, removed the freezer racks and removed the back panel to expose the evaporator. I removed the defrost thermostat, unplugged the wires, and installed the new thermostat. I replaced the panel and racks then removed the defrost timer kit by removing the two screws that fastened the cover to the refrigerator and the two screws that secured the timer to the cover. The timer is centered behind the front toe grille assembly. I installed the new timer, replaced the cover, and plugged the refrigerator in. It took several minutes for the defrost timer to advance before the evaporator fan would come on.

Removed door. Removed old cam closure assembly. Noticed that there was almost nothing inside the door for screw to screw into(only styrofoam insulation), which is why original screw backed out. Bad design. Got longer screw at bigger diameter. Pushed high strength glue into hole, on screw threads, and underneath screw head. Assembled. Crossed fingers. About three weeks have passed and so far, so good.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

noticed the fridge and frezzer were not cold one day.i got on google and typed in the problem and found out the the relay goes bad rather often. was an easy fix. found the parts here on partselect and recieved in with in 2 days of ordering. pulled the old part out put new part in and plugged fridge in and was back up and running with in minutes..thank you partselect....

Removed the hinge cover, removed three hinge screws, removed door. Then I used a screwdriver to pry out the hinge bushings, pushed the new ones in and replaced the door. Both Maytag and Lowe's (who held the extended warranty) said that the door was not a repairable item and would have to replace the whole door. Since that would cost more than the value of the fridge, they voided the warranty and returned my cost. Too bad we didn't know about Part Select, we would have held their feet to the fire.

While investigating a water leak I discovered the condenser fan seized. I removed the fan to prevent a fire and ordered the part. The hardest part was identifying the correct fan. That took longer than the installation.
I cut the wires and spliced in the new motor. It rotated correctly and I replaced the crill.
Done
Total time of ice maker water leak repair and fan replacement about 1 hour.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

First step, call the repair man. He listened, and then said to get a new refrigerator, since this one is 28 years old and the repairs could amount to a significant part of the price to buy new. Even if he fixed this, it could develop other problems, yada. So we went out to buy and discovered nothing suitable that would fit in that slot of our kitchen! We'd need new counter top and cabinets to fix this problem! So we went to the Internet and searched to find the likely source of the problem and the parts schematic at PartsSelect.com. Yah! We ordered the part, and then found we had no idea how to install it. Sooo, back to the Internet, and eventually got some good clues - it goes in the kick space under the front, and just plugs in, once you can get to it by removing the bracket that holds it. Working underneath a refrigerator is not complicated but it's awkward. The form of the new timer was not exactly the same, but it does function correctly. We have no experience whatsoever with appliance repair, so pretty amazed at our success. This old Amana looks very good inside and out and is now working perfectly again. If it lasts a few more years, we will be thrilled to have spent $15 to save $500. We can always buy new later on.

1. Removed the cardboard cover.
2. Removed the terminal block and unplugged the old motor.
3. Removed three screws that held old motor to the bracket.
4. Removed the fan blade from the old motor.
5. Installed the fan blade (after cleaning) to the new motor.
6. Crimped on new wire terminals onto the leads on the new motor.
7. Installed the new motor using the fasteners provided.
8. Plugged the new motor wires onto the proper terminals in the terminal block.
9. remounted the terminal block.
10. reinstalled the cardboard cover.

I first removed the panel in the bottom so I could see the fan and the Bimetal thermostat. Also removed back panel so I could see the tester wire and make sure I was going to be able to pull it though the small hole. Removed the old thermostat. Clipped new one on made sure I had reconnected all plugs correctly. Turned on refrigerator and waited about 30 minutes to see if fan kicked on and all was good replaced panels. This was totally great for me, I'm a woman and for me this was very exciting for me to be able to fix it myself without having to call in a repair man or just replace the refrigerator.

Unplugged the machine removed the bottom plate and back plate and ice maker.Removed 2 wires to motor and ground wire.Removed 2 mounting nuts for motor,installed new motor and used old fan blade for new motor .Reinstalled in reverse order plugged in and tested fine.