ARR6400WP1143457NW Amana Range - Instructions

just plugged it in!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

First I removed the two screw on the lower inside of the door that hold the door to the hinges. Then I opened the oven door at about a 15 degree angle, and carefully lifted the door out of the hinge brackets. Next I had to remove the side panels on the door . After getting those side pieces off, I realized that I had to go through all layers of the door to get to the inner glass, so I decided that the best way to keep track of all those screws, was to remove each screw with the Phillips head screw driver, and immediately scotch tape that screw right next to the hole it came from. That was the best idea I had, because there are many screws in that door! Removing the old glass, and replacing it with the new glass was the easiest part of the project, just be sure not to let pieces of the insulation get between the glass and the metal frame. Then I reversed my steps to put everything back together. It probably took a bit longer than someone else because I first taped each screw on the panels, and then had to remove the tape, but I just did not want to find a handful of screws after the door was back on, or worse, somehow lose one or two. I think the hardest part of this project was getting the door back on the hinges, because the door is heavy, and you have to line up the hinges with holes in door, and slide the door in evenly. Once the door is back on, re-insert the two screws, and your oven door is as good as new (and as clean as new).

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Indicators showed broiler should be working so basically made a guess that the element was bad and replaced it. Turned off circuit breaker and removed mounting screw and unplugged terminal ends of the element and replaced with new one. Switched circuit breaker on and turned on broiler and my repair was a success.

Turned power off! Removed two mounting screws, disconected two slip on wire terminals from heating element. Removed Element from oven. Took about 10 minutes.
Part came in two days. Re installed heating elemet by pushing on the two slip on wire terminals and re installing the two mountint screws. Took about 10 more minutes.
We have been retired for 17 years. Wish all my "Honeydew jobs were this easy!

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in.
The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.

Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!