ARR-201 (P85450-4S) Amana Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drip bowls were burned and tacky
First I removed the old bowls and replaced them with the new.
Parts Used:
-
Donna from Dallas, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
471 of 478 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowls needed to be replaced
took old bowls out, put new bowls in, took a coffee break
Parts Used:
-
John from Chester, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
453 of 542 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans stained
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!
Parts Used:
-
Linda from Atlanta, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
216 of 425 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We needed new drip pans and no one carried the model we needed
we removed the old pans after first removing the electric heating element and simply inserted tne new pans
Parts Used:
-
sylvia from ventnor city, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
67 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Purchased home but stove had no broiler pan.
-
Raymond from BLOOMINGTON, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
14 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler burned out
The Job didn’t take very long at all. I pulled the unit out and unplug it before I started the repair. I had to remove the back two access cover plates to get to the two wire leads that connect the broiler. I don’t believe there was enough wire to be able to do it all from the front side. Next I disconnected the two wires that connected it while remembering what color goes to the correct side (just incase this does matter). After removing the wires I moved on to remove the element with a Philips screwdriver. The new part already had the hangers on it so I reused the old screws and installed the new element. Next I reconnected the wires in the back and re-installed the back panels. I plugged it up and it works as good as new now. This was definitely a lot cheaper to fix this myself than hire a repairman.
Parts Used:
-
David from Lewisburg, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
-
Janet from Philadelphia, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Parts Used:
-
Sharon from Yacolt, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
elements were broken
took out the old ones and replaced them following the instructions provided by you. thanks
Parts Used:
-
CARLOS from DEVINE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Parts Used:
-
Carl from RIVERSIDE, CA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broil element broke
Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.
Parts Used:
-
Randall from Cartersville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drip bowls were all caked and corroded.
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Parts Used:
-
Terry from Mountain City, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler Element went out
I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part!
Parts Used:
-
Michele from Salem, OR
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Parts Used:
-
Yafa (and David) from Bothell, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
5 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned out element
Shut off power to the oven.
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!
Parts Used:
-
Neil from Oak Park, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!