1. Home
  2. ALZ8580ADQ
  3. Instructions

ALZ8580ADQ Amana Cooktop - Instructions

All Instructions for the ALZ8580ADQ
46 - 60 of 64

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner rusted flames coming out the side of the burner
  • Lewis from Tomahawk, KY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right
Was this helpful?
Thank you for voting!
Bottm Of Burner Rusted Out
  • Paul from Oxford, MA
  • Really Easy
  • Less than 15 mins
Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.
Was this helpful?
Thank you for voting!
Igniter not working
  • Casey from Soledad, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this helpful?
Thank you for voting!
Flame coming from under burner cap
  • Tom from Fenton, MI
  • Really Easy
  • Less than 15 mins
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Was this helpful?
Thank you for voting!
No ignition of gas stove burner
  • Andrew from San Francisco, CA
  • Really Easy
  • Less than 15 mins
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Was this helpful?
Thank you for voting!
The old burner was rotten and leaking
  • Michael from Santa Barbara, CA
  • Really Easy
  • Less than 15 mins
Pulled up the old burner, disconnected the ignition wires, re-connected them to the new burner, replaced the new burner in the stove and presto - everything worked as it should.
Was this helpful?
Thank you for voting!
range top was missing one of the rubber grommets used to hold the grate.
  • John from Elizabeth, CO
  • Really Easy
  • Less than 15 mins
Just pushed the new grommet into the hole. The grommet fit just fine and took about 10 seconds to install.
Was this helpful?
Thank you for voting!
The igniter on my stove wouldn't ignite.
  • keith from massillon, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
Was this helpful?
Thank you for voting!
Old burner rusted, flame bypassing
  • Pete di from San Diego, CA
  • Really Easy
  • Less than 15 mins
Simply twisted to remove from range top, slipped off igniter wires, attached to new burner, and twisted back into place on range top. Works great,
Was this helpful?
Thank you for voting!
the top broke away it was corroded
  • Thomas from Floral park, NY
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Was this helpful?
Thank you for voting!
Burner flame was poor and yellow flames left sute marks on pots and pans
  • Jeff from Oconto Falls, WI
  • Really Easy
  • Less than 15 mins
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds
Was this helpful?
Thank you for voting!
Rubber grommet for stove top cover
  • Lisa from Plymouth, MA
  • Really Easy
  • Less than 15 mins
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Was this helpful?
Thank you for voting!
Gas blowing out from under burners
  • Dean from Mobile, AL
  • Really Easy
  • Less than 15 mins
  • Pliers
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the c ircuit breaker box. The video was extremely helpful.
Read less
Was this helpful?
Thank you for voting!
Burners won't light up
  • Bhavni from Richmond, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this helpful?
Thank you for voting!
Wore out burner and igniter
  • Bruce from Vashon, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
New burner and igniter.....actually it was very easy to to fix
Was this helpful?
Thank you for voting!
All Instructions for the ALZ8580ADQ
46 - 60 of 64