AGDS902E Amana Range - Instructions

Took off the burner by unscrewing the two screws and lifting out the burner/igniter together being careful to not let the electrical connection come apart. If it does then you have to take all 4 burners off so you can lift the whole oven/burner top. Disconnect the old igniter by (more than likely) drilling out the old screw, if you are lucky maybe the old screw holding the igiter will actually unscrew. If not, you can put a new screw in to hold the new igniter, put it all back together and youre done.

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

The key to this repair was making sure I typed in the correct model number and serial number so that I got the correct part. I had read here that a couple of folks had received the wrong temperature sensor (i.e. it had the male plug instead of the female plug). Unfortunately I had to call the local appliance repair guy as the plug could not be accessed from the interior of the oven. It was easy to remove the 2 screws that held it in place but I could not pull enough of the wire out to access the plug. The local repair guy pulled to oven out and removed the back in order to unpluy the bad sensor and plug in the new one. It was actually kind of nice that he came as he used a digital thermometer to cycle the oven through a couple of warm ups to see if it was actually working correctly. It worked fine and my wife was happy again. The $75 I spent on the repairman was darn well worth it. "Happy wife = happy life!"

simple repair 4 nut screws easy

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.

Remove two phillips screws, lift the burner head up and remove the wire from the electrode. DO NOT DROP THE WIRE!!! It will fall into the stove top, adding much more time and frustration to this very simple repair. Reverse these steps to complete the repair.

Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems

Removed grill cover, took out old filter and placed new filter, placed grill back over filter. Back in business!

First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013