All Installation Instructions for General Electric Range AGBS45DEF1WS

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Getting thew the back

I put it in the same way tuck it out

Parts Used:

Oven Thermostat

William from BOSCOBEL, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven bottom badly marred after 16 years.

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Charlie from NAPLES, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

burner cap wasn't working proper.

took burner off installed new one thank you for fast shipping

Parts Used:

Burner Cap

GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Front orifice tube broke

The repair went easy the tube was a perfect fit

Parts Used:

Left Front Orifice

craig from unadilla, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

4 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 8 people found this instruction helpful.

Was this instruction helpful to you?

My oven bottom got rusty

I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Mary from Redondo Beach, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

Was this instruction helpful to you?

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Parts Used:

BRACKET ANTI-TIP Assembly

Greg from Ft. Washington, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

carbonized burners

Replaced all four

Parts Used:

Small Burner - 5K

Burner Head - Medium - 9500

Burner Head - Large - 12K

Stephen from North Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Parts Used:

Burner Head - Medium - 9500

John from Los Angeles, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Parts Used:

Burner Head - Large - 12K

glen from felch, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The oven door gasket was worn and didn't provide a good seal.

I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.

Parts Used: