All Installation Instructions for General Electric Range AGBS45DEF1BS

Needed To Replace Burner

Took longer to open the box.

Parts Used:

Small Burner - 5K

Robert K from York, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Burnt burner

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Parts Used:

Burner Head - Medium - 9500

Janine from Wind Gap, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

I needed another oven rack. It came with two. Now I have three.

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

Parts Used:

Oven Rack

Frank from N ROYALTON, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not turn off due to inoperative thermostat

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

Parts Used:

Oven Thermostat

Timothy from Lake Elsinore, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Oven door gasket was missing.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

Parts Used:

GASKET DOOR ASM

Eugene from TUSCALOOSA, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

burner caps began to chip

I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.

Parts Used:

Burner Cap

Burner Cap - 5000 BTU - Black

Anne from Plainview, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.

I JUST EXCHANGED THE BURNER AND BURNER CAP.

Parts Used:

Burner Head - Medium - 9500

Burner Cap - Black - Medium - 9500 BTU

Astrid from MORAGA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Burner on stove not working correctly

Order parts and installed - no tools needed - completed repairs less than 1 minute

Parts Used:

Burner Head - Medium - 9500

Trevor from Eldersburg, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Replace Gasket to Oven

Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.

Parts Used:

Gasket

Nancy from BRICK, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

Parts Used:

Oven Thermostat

Leroy-Anthony from Jamaica, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Hard to remove screws & no instructions that a heat shield had to be transferred from old to new

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Peter from REDDING, CT
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

No ignition

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Parts Used:

Oven Thermostat