Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The old shelf shattered when we tried to clean it
2 of 2 peoplefound this instruction helpful.
Michael from COAL VALLEY, IL
Easy
30 - 60 mins
Just slipped it in. I think it's a very poor design.
Was this helpful?
Thank you for voting!
My refrigerator vegetable bins were sagging when I placed veggies in it.
2 of 2 peoplefound this instruction helpful.
Lee from SAMMAMISH, WA
Easy
30 - 60 mins
Screw drivers
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 peoplefound this instruction helpful.
Marc from SEASIDE, CA
A Bit Difficult
30 - 60 mins
Screw drivers
I replaced the Control Board... the two boards need to be installed first . than plug in the connectors (refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper
... Read morely and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!
Refrigerator was warm,freezer was cold
2 of 2 peoplefound this instruction helpful.
Henning from RHINELANDER, WI
A Bit Difficult
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattachin
... Read moreg rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!
Read less
Was this helpful?
Thank you for voting!
Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.
2 of 2 peoplefound this instruction helpful.
Jim from HALTOM CITY, TX
Easy
15 - 30 mins
Screw drivers
The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one or
... Read moreientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.
Read less
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 peoplefound this instruction helpful.
Gerald from COLORADO SPGS, CO
Really Easy
30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
Broken drawer slide
2 of 2 peoplefound this instruction helpful.
Irvin from Louisville, KY
Very Easy
30 - 60 mins
Screw drivers
Extremely easy. Probably could have been done with eyes closed.
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 peoplefound this instruction helpful.
Brent from PRESCOTT, AZ
Really Easy
30 - 60 mins
Nutdriver
Super simple following the instruction video you posted. Thanks!
Was this helpful?
Thank you for voting!
peg that swings the pantry door open and closed was broken off
2 of 2 peoplefound this instruction helpful.
Dalton from BEAUFORT, NC
Really Easy
1- 2 hours
Nutdriver, Screw drivers
watched partsselect video and simply followed the directions
Was this helpful?
Thank you for voting!
Rear mount tab broken on Center Crisper Rail
2 of 2 peoplefound this instruction helpful.
Joseph from Live Oak, FL
Really Easy
Less than 15 mins
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this helpful?
Thank you for voting!
When the support frame broke we threw the entire system into the trash DUH !
2 of 2 peoplefound this instruction helpful.
Bruce from CLARKSVILLE, VA
Really Easy
Less than 15 mins
Thanks for the video showing how to replace the Humidity Slide the knowledge that the end with the flair needed to be slightly bent to SNAP into place was a big help.
This is the small part that is critical to having a fully usable refrigerator but one that no one (even an authorized shop) has in stock. Just pop it back in, and you're done.
Was this helpful?
Thank you for voting!
Deli drawer support had broken
2 of 2 peoplefound this instruction helpful.
Glenn from NEW ALBANY, IN
Very Easy
Less than 15 mins
Screw drivers
Ordered a replacement Deli Drawer Guide for the right side. Very simple repair, the plastic deli drawer guide is attached to the metal shelf support with two phillips screws. the repair was completed in less than 10 minutes.
Was this helpful?
Thank you for voting!
The right door gasket was cracked in two or more places and probably leaked.
2 of 2 peoplefound this instruction helpful.
JAMES from BREVARD, NC
Very Easy
Less than 15 mins
I watched the Part Select demonstration for removing and replacing the door gasket. It looked easy and was easier and faster than the demo. The toughest part was getting the wrinkles out of the new door seal.
Was this helpful?
Thank you for voting!
After 19 years of use, both side glides of deli tray had cracked.
2 of 2 peoplefound this instruction helpful.
Liz from ELMHURST, IL
Very Easy
Less than 15 mins
Just 2 screws on each side - took them out, installed new glides with existing screws. Very easy - ended up giving the fridge a thorough cleaning - fridge cleans so easy and quickly.
My Orders
