AFB2234WES4 Amana Refrigerator - Instructions

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

My son (who does HVAC, but not appliance repair) did some investigating by taking front and back panels off and determined that the evaporator coil was freezing over because the defrost wire was not heating up. He and his girlfriend did some real-time internet searching for diagnostic info because NO control diagram was included with the refrigerator. He determined the problem was most likely the electronic control board. Ordered and installed a new board and the refrigerator is back to working fine. Took about 2 hours to diagnose the problem and 1/4 hour to actually install the control board. Kind of disappointing that this control board failed when the refrigerator was less that 4 years old.

Followed the video and installed the new Jazz board. The board cam in 1 piece which had to be separated into two pieces, but the scored area on the board made it less intimidating. At the same time I replaced the two incandescent lamps in the refrigerator area with LED lamps. Getting the housing for the control board apart was the most difficult part, installing the replacement board was a breeze.

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

Since there were no instructions, I was a tad hesitant but dove in. I was just replacing the right end cap, not the left. Removed the involved shelf as well as the two drawers above. Undid the three screws involved and carefully removed the slide rail end cap as well as a part in the back that was attached. That was the hairy part. It took a bit of time to remove it since everything seems so brittle but I was careful and got the assembly out without breaking anything. Also had to remove the slide rail and humidity control. Nothing to removing and replacing the slide rail. You just have to put it back correctly oriented. This was easy. I just looked at the one on the left, which I hadn't removed. Most time consuming part was cleaning things that were normally inaccessible, before re-installing.

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Ordered the part. When came in I took it out of the box and slid the two end posts into the provided holes. Lid fixed in less than 5 minutes. Part came in on the third day because I ordered on Friday afternoon.

We snapped the new one on correctly this time.

Removed the shelf, attached new glide, and replaced shelf

The part came the next day, very quick. The wrong size ended up in box we recieved. The part # we ordered was correct, just a mix up in the packaging process. I called and the customer service dept. had a new correct crisper pan delivered to my door two days later. Even with the mix up it was very fast and a good price compared to other sites. I would order again in the future.

I contacted partselct to see if I could get the end caps with new hinges to correct the problem. My customer service contact was very professional and a huge help in helping me select the correct parts. When the parts arrived I was amazed they were genuine whirlpool parts, fit perfectly, and were easy to install. I have other parts to order and will use partselct again. I appreciate everything they did for me to solve this problem.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

Ordered new fan motor
Got part took fridge apart
Result was the motor was running
The fan blade had come off the motor
Replaced the motor anyway and reinstalled the fan, working well