All Installation Instructions for Admiral Range AER1110BAH

Oven Racks were old

Replace the racks. No special instructions.

Parts Used:

Oven Rack

Sandra M from DISTRICT HTS, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner swith not working properly

removed 4 screws lifted off the face with switches replaced the bad switch and put the face plate back on. if you have any concerns just watch the video , part select has posted its great

Parts Used:

Range Infinite Burner Switch - 8 Inch

leland from CARTHAGE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Infinite switch replacement.

I followed the instructions as provided. When I finished I noticed the switch was 1/4 turn out from the off position mark on the stove. So I pulled the stove back out and took the back panel off again pulled the knobs back off took out the screws that held the switches in place and rotated the switch 1/4 turn counter clockwise. Then I replaced all the screws and knobs . Then I replaced the panel and shoved the stove back in place. One of the burners was an eight inch and the switch doesn't work as well as it could. However there was not a direct replacement for the eight inch burner.

Parts Used:

Infinite Switch - 6 Inch

William from Kerens, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

1960's oven door gasket fell apart, actual gasket not available any more

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Parts Used:

Door Seal

Mary from WINCHESTER, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My original back leg broke because the floor is uneven. Had to pull it out several times.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Phyllis from BROWNVILLE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My oven door seal had dried rotted

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Parts Used:

Door Seal

Anita from ELKTON, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

element burnt out

super easy after watching the how to video you had on it and iam the wife not the husband it was so easy thanks

Parts Used:

Bake Element

richard from KAUKAUNA, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heating element stopped heating

I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.

Parts Used:

Bake Element

Miguel R from MCKINNEY, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

element burned out shortly after purchase of range, one was purchased locally and did not fit properly, causing element to burn out

replaced element with new one , worked perfectly-

Parts Used:

Surface Burner Element - 8 Inch

Sue from INDIANOLA, MS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner receptacle failed (stove over 30 years old)

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.

Parts Used: