AE4113 Dryer - Instructions

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.

The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

remove front part of the dryer and rise up the top to remove drum to replace the belt. than remove two screws for the heating element piece of cake repair.

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

Disconnect power and pulled the lower front panel off unit (2 screws).
I used a ohm meter and found heater coil open. Ordered correct part online (easy to find it on the web site).
Three days later, new part in hand I unplugged the failed unit's wiring and removed the heating unit (2 screws). Installed the new part, connected wires and reinstalled the four screws.
Engaged power and turned the dryer on. Vent pie had heat, so placed wet clothes in unit and ran a dryer cycle. Works like new. Cost was about $65.00 versus the $500.00 for a new dryer.

Removed the 2 screws from the bottom of the front panel and pulled the cover up and out. Labeled the wires to the light and door switch and disconnected. Lifted the belt tensioner arm and unlooped the belt from it and the motor. Removed the 4 bolts that hold the front drum support on then held the drum up and removed the support. Pulled the drum out slightly and allowed the rear to drop, at this point you can get to the rear rollers without pulling the drum out of the machine. The roller shaft was so tight I had to put a straight-blade bit in a 1/4" socket to get enough torque to break it loose. Make sure to use a large enough driver or you will strip the slot out of the screw. This model had a nut on the back but I was able to just drag my finger against it to get it apart. Removed the washer and roller from the shaft and cleaned the shaft and washer with WD40 before reinstalling with the new roller. Vacuumed all the lint I could get to and reassembled, lift drum, push back, front support, 4 bolts, belt, wires, front panel, 2 screws.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

Followed video on PartsSelect website, they made it real easy.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.