ADW662EAW-PADW662EAW0 Amana Dishwasher - Instructions

Remove lower cover to expose the motor, valves and electrical connections. turn off water supply and electrical circuit breaker. Disconnect leads from float switch. Remove float switch with a single phillips head screw. Replace with new one and attach leads---very easy.

Remove water inlet electrical connections--remember which goes to which connector. Disconnect hot watter supply with open ended box wrench.
Remove water inlet valve from washer wall by unscrewing two sheet metal screws. Use 1/4" socket and 3" extension for this. Use pliers to release the hose clamp holding the rubber water line onto the valve outlet stem. Reverse this sequence to intall the new switch. Moderately easy. Have sponge and paper towels to soak up spills when you do the disconnects.
.

Once I figured out how to get the endcap off the roller track (allow several minutes, because it was designed by some dork), I slipped the old roller off the track, put the new roller on, and clipped it to the rack. Then I put the track cap back on (really easy once you've figured out how to get it off) and it was good as new.

As for how the cap comes off, it's difficult to describe. But it may help you to know that the cap, despite what it looks like at first, is actually surprisingly long and folded on top of itself. Pulling it directly out doesn't work; you have to unfold it before there's any chance of getting it out.

I removed the two plates located below the dishwasher door to expose the float switch. I removed the two screws holding float switch, I removed screw holding switch actuator, then I removed float assembly.
Installed new float assembly, but could not use the float palnut, it had too small of a hole, I substituted a larger one that fit the float better. Note I fitted the palnut to the float (the nut cuts it's own threads in the float) before installing the float. This made installation easier. Next I transferred the two wires from the old float switch to the new float switch in the same positions as the existing switch wires. Then I installed the float switch. Finally, I cleaned up the float switch actuator and screw so that the actuator moves freely on the screw. I then installed the float switch actuator and ran the dishwasher to check for proper operation. Note: this float and switch control the water level in the dishwasher. If the actuator sticks, the dishwasher will fill with too much water and leak. If the float has collected dirt inside, it will weigh more and the water level will be too high, causing the dishwasher will fill with too much water and leak. If the switch sticks or fails the water level will be too high, causing the dishwasher will fill with too much water and leak. That is why I relaced the parts: float and switch. I don't want to go back and work on this again.
Lastly, after a few days of proper operation, I installed the two plates located below the dishwasher door. Job done!

snapped on new roller and job done

removed the door gasket by just pulling it out and pushing the new one in its place. very easy, took five minutes at most. Then removed the 7 screws holding the inside of the door in place, removed the dispenser assembly, held by two drive screws and replaced the dispenser door latch grommet. Finally, removed the insulation foam gasket. Had to scrape the old adhesive from the door as the old a\gasket had disintegrated. This took the most time. Then just pressed the new foam gasket in place. Reading the comments from others was a big help. Don't think I would have replaced the dispenser grommet had I not been warned about it. I'm sure it was part of the problem. All is well now, no leaks.

First, removed end cap in steel sliding upper rail, second, removed broken roller, third, attached new roller, you can look at other rollers to see how it goes on, fourth, feed new roller into track, replace end cap. Takes less than 10 min, saved 85. 00 Bucks.

Took off old part. Modified new roller w'knife. Found a nut and bolt in scrap pile. Attached.

I first turned off the water to the dishwasher, then the electricity to it, then took off the front bottom access panel, I then unbolted the inlet valve from the side of the machine, undid the electrical hookups remembering which one connected to which, then unclamped the two hoses, I then put the new one back in place, redoing the hoses and electrical and bolting it back to the side of the machine, then putting the front bottom access panel back on, then turning back on the water and electicity. The one thing that may make it easier if you can is to pull the dishwasher out from under the cabinets and lay it down so the bottom is exposed. This would make the process a little smoother.

I pulled the interior of the door until I was able to get to the switches on the door latch. I determined at least one switch was completely worn while the other worked minimally. I then looked for the latch assembly and found out that it was no longer available. So I did some searching and found the exact switches I needed from PartSelect. The switches came in about 3 days which then I installed them. The dishwasher powered right up and stayed on. So in the end it was much cheaper to repair this unit than buy a new one right now. Plus, my wife is happy and so am I. Thanks PartSelect for carrying the parts I needed.

This ended up to be a (2) phase project. The first repair was to replace the door seal and inner door foam. Thanks to earlier online comments this part was really easy, but we still had a small leak. When I had removed the interior face of the door panel to replace the inner door foam, I had noticed the insulation was wet and deducted that the 'soap cup door latch gasket' was the real culprit so I had to place a second order (Phase 2). The order came quickly and in time for next Saturdays to to list. My advice is to replace all 4 items at the same time and save on mailing cost and repair time; reservoir O-ring, soap cup door latch gasket, inner foam gasket and door gasket. net repair time, about an hour start to finish.
Don and Rosie
Rochester, NY

The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It was installed right over the previously installed strip and made a tight seal. (knock on wood)

First, I removed the foot plate(s) at the bottom of the Dishwasher. (2 screws each side)

Then I removed the two top screws at the front of the dish-washer. The screws were mounted into a board under the counter that had broken loose. (A minor secondary issue specific to my situation.)

I gently inched the dishwasher out from under the cabinets.

SLOWLY, I tipped the dishwasher over on its side, allowing the water still inside to drain into a pan. Minor cleanup required for the cup or two that missed.

I then had access to the part. I disconnected the power from the wall socket, and I closed the valve for the inlet water from under the sink.

I removed the screws holding the Water Valve to the DishWasher case. Then I took a sharpie and marked one side of one of the two power connectors, black-mark to black-mark.

When I went to disconnect the inlet pipe, there was more dripping than I expected, so the valve under the sink was not closing completely. I needed to shut off the water supply to the house for the next stage.

I disconnected the inlet water supply, which continued to drip slightly into a bucket. I then removed the coupler from the old water valve. It was badly clogged and corroded, so I went to a local HW store and found an exact match 3/8" to 3/8" right angle coupler with compression fitting on one end.

BIG TRICK, before installing the new coupler, WRAP the compression fitting threads with teflon tape. You will not be able to wrap it once it is installed. In fact, I needed to uninstall the part once after I discovered this, to wrap the threads smoothly.

Once pre-wrapped, wrap the other threads that screw into the water valve. Tighten until secure, AND aligned with the direction of the flow tubes of the original.

Match the electrical connectors, black-mark to the same position as before. (The new water valve will NOT have the black-mark on it, unless you transfer one!)

Connect the Water valve back to the Dish Washer chassis with the two screws previously removed.

Connect the inlet water back to the compression fitting with the pre-wrapped threads.

Gently return the dishwasher to upright, and then plug it in.

Open the valve under the sink slowly and watch for drips or leaks.

Run the dishwasher at the start of a cycle, long enough to determine that the valve activates, and allows water to flow. Then stop the cycle.

Gently walk the dishwasher back under the counter, observing that you do not kink the copper water inlet pipe, or the drain pipe.

Adjust the feet, if necessary, back to fully support and level the dishwasher.

Install the two screws holding the dishwasher to the cabinet front. Then install the kick plates and tighten those 4 screws.

Clean up any residual water from the process.

I surfed the net using phrases like "dishes not clean" and found a series of possible solutions. When I noticed that the water in the washer was cold, I realized it was a heating element issue. Using a multi-meter set to the lowest resistance I tested both ends of the heating element (OF COURSE I SHUT OFF ELECTRICITY TO THE DISHWASHER FIRST!!!) and found it read a steady 16 ohms. Then I followed the orange leads to the limiter, removed the leads and tested resistance and found it at near zero. Touchdown.

I ordered the new limiter, had it in a couple of days and installed in in 5 minutes. The hardest part was putting the metal cover back on the bottom of the unit.t

I first disconnected power from the dishwaher at the breaker panel. Then, removed 4 screws on the front of the dishwasher and removed the lower panel. I removed the two wires (compression fittings, by hand). Then I used an adjustable wrench to remove the two nuts which retained the element. I opened the diswasher door and extracted the old element. I reused the rubber O-rings from the old element and placed the new element into the dishwasher. I replaced the nuts and wires. I reenergized the circuit and ran the diswasher through a normal cycle. Note: I had plenty of towels on hand just in case the old O-rings did not perform. No problems encountered. I replaced the front cover and loaded have checked under for leaks during the last two wash cycles. Note: be sure not to over tighten the element nuts as they are plastic and will strip out. I used the model number to obtain the new part and all went flawlwssly. Thans!

float was missing palnut and letting the float slide up too much causing small leak around the float