All Installation Instructions for General Electric Dishwasher ADW1100NW

Dishwasher would not drain

Replaced impeller

Parts Used:

Impeller and Seal

Ed from RICHMOND, TX
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Could not get the arm to close.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Parts Used:

Detergent Cup Release Arm

David from Pembroke Pines, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins

4 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Rear wheels wouldn't roll, so bottom rack had to be lifted into place. Backbreaking.

The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Jane from La Quinta, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

wheels colapsed

replaced new wheels

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Nick from Chatham, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher pump was frozen

Ordered pump mechanism and replaced defective pump. A very easy replacement

Parts Used:

Pump and Motor Assembly

George from Loving, NM
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

4 wheels missing from diswasher rack (lower)

removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Richard from Oak Hill, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

wheel was distorted

Simply replace wheel

Parts Used:

Lower Rack Wheel Kit - 8 Pack

R. Cecil from Norfolk, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

bottom shelf would not roll properly

so easy! Ordered the rollers and clips ... popped them on and done!!!

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Denise from Fair Oaks Ranch, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

bottom basket of dishwasher kept following out

i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket

Parts Used:

Lower Rack Wheel Kit - 8 Pack

stephen from mashpee, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Leaks

All new seals

Parts Used:

Door Gasket - White

Kelvin from Sun City West, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Water leaking out from bottom of Dishwaser

Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!

Parts Used:

Water Inlet Valve

Donna from Arlington, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Door had no resistance/no balance/would fall open

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

Parts Used: