ADT521PGJ0WS General Electric Dishwasher - Instructions

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.

youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott

1. Take a picture of the old rack in the dishwasher! Just in case!
2. Remove rail channel end caps and place them on the tabletop on the correct side to make sure you put them back on the correct side.
3. Remove old rack.
4. Carefully snap off the water sprinkling unit. (carefully push down tabs so they don't break).
5. Using your picture as a reference (!) snap the water sprinkling unit on the new rack (it's easy).
6. Put the new rack back onto the rail channel and replace the end caps.

Done! Very easy installation ! Rack was not nearly as expensive as I anticipated and was delivered quickly. Note: You get the rack only. All ot the other parts are from the old unit.

The repair is easy for most if you have basic skills.

1. Cycle your unit to make sure all the water in the tub is emptied. (Start a cycle then cancel it which forces it to empty)

2. Turn off the power at the circuit/fuse panel & also turn off your water supply going to the unit which is usually under the sink with your sink plumbing.

3. Have a few old towels handy, there will be a little water but nothing that requires a wet shop vac, etc.

4. Remove the bottom kickplate (should be a screw on each side of the front of unit)

5. Disconnect the power supply wiring to make removal easier.

6. Disconnect the water supply line (have a towel handy there will be a little water in the supply line)

7. Unscrew the mounts either at the top and/or sides of the washer depending on the install method into your cabinetry.

8. Carefully slide out the unit.

9. Carefully turn the unit on its side or upside down depending on your preference to work on the underside where the pump is located. Again have a towel or two handy there will be some water that leaks out from the tub even after forcing an empty cycle.

10. The circulation pump is easy to remove. First plug the power line, there is a clip to disengage to separate the plug. A small flat screwdriver will help.

11. If this is a first time being replaced it will probably have crimp style hose clamps on the two lines coming off the pump. Again a small screwdriver will help pry it apart. Throw these away your pump kit will have new hose clamps for installation.

12. Once these clamps are removed you can slip the hoses off and the pump will be free to remove from the unit.

13. Installation is easy. Make sure the rubber hoses seal completely around the unit before clamping. Pay attention to make sure its sealed evenly, your unit will leak water otherwise once its functioning again.

14. My recommendation is to reassemble, slide the unit back into your cabinetry and hook your power and water supply up. Before you screw the unit back into place and close up the bottom panel, start a quick cycle. Within that first minute when the unit is filling and starting the circulation pump you can watch underneath and make sure your circulation pump lines are sealed and not leaking. Once satisfied, you can then stop the unit and finish securing the unit with mounting screws and closing up the bottom kickplate panel.

Good luck! You can do this :)

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute