ADB2500AWW3 Amana Dishwasher - Instructions

took screws our of side trim and top trim, decreased height on leveler legs and pulled dishwasher from the cabinet, replaced cables and springs from both sides on the door, lubed door hinges cleaned everything under dishwasher re-inserted and re-installed trim screws. took around an hour with clean up.

We took out old racks and installed the new ones. On another note, after ordering (or trying to order) parts from appliances older than 10 years old several times, I think manufacturers stop making parts after 10 years. So if you're thinking of replacing a part on an older appliance, try to look for it sooner than later.

The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

Take out 12 screws, replace the handle assy, replace the screws in door, done. Took every bit of 10 minutes. I used my power screw-driver with a torx bit.

We couldn't order just the handle - the entire assembly was around $25 - less than a service call. I read beforehand how easy this was, but I couldn't get the old assembly to "unplug" from the existing prongs and wound up just removing the ceramic pieces from the new assembly so I could leave the prongs plugged into the old. Works fine, but still have no idea how to unplug those prongs and it was frustrating to have paid for the new ceramic parts and not be able to use them. Rated it as "easy" instead of "really easy" because of that.

Open door fully. Remove all screws that hold inside panel to Front panel. Carefully remove Inside panel being VERY CAREFULL not to pull wiring out of door switch [top of door] and operator switch panel [also top of door]. Remove door switch, next remove 3 screws holding switch panel in place. Remove the top plastic section where switch panel mounts and set aside. Carefully remove green ground wire from bottem hinge for door. [right side] Next CAREFULLY remove front panel from hinges using EXTREME CARE not to let hinges "free fall" to the open position. Remove old panel. Install new panel in the reverse order as the old one was removed. DO NOT PANIC if you happen to pull the "ribbon cable' out of panel switch. It will plug back in very quickly and only one way. Just make sure it is "seated" in plug. The "key word" for this panel replacement is CAREFULLY.

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

In less than 5 minutes we took the screws out, fixed the latch and had it back together again. The amazing part of the story is the perfect diagrams and helpful instructions from Part Select. I ordered the part one day and by noon the next day the dishwasher was fixed!

removed the screws that held the inner panel. removed the handle from its electrical connectors (2) reinstalled new unit and works like new.