ADB1100AWB0 Amana Dishwasher - Instructions

The repair went okay. The problem was that the dishwasher would not run after the installation of the dispenser. The door was taken apart 2-3 times. I told my husband (the repair man) that we should pull out the dishwasher so I could clean behind it. I asked him 4 or 5 times to pull out the dishwasrer. Never an answer. Mind you he is an electrician by trade now retired. For some reason while I was not looking he did pull the unit out after 2 hours of fussing with this electrical problem. Remember he is an electrican by trade. When he pulled the unit out "THE PLUG WAS OUT OF THE SOCKET". How funny!!!!!!!!!!!!!!!!!!!!!!!!!!
I could not stop laughing. I had to answer the phone at that time and my friend thought I was out of breath from running for the phone. I told her later it was from the PLUG OUT OF SOCKET TRICK. I still am laughing. The first thing an repair mann will ask you is if the unit is pluged in. I have two sons and one son-in-law that are electricans and will have many years of fun telling this story. It is good to laugh. I will be laughing for a long time.

I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Repair was easy. Step by step instructions on touTube

quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Followed directions from YouTube video.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Bought the new cap, took it out of package, installed.

Removed old arm and put knew one on!