All Installation Instructions for Maytag Range ACR4503SFB2

Replaced screw

By hand screwdriver

Parts Used:

Range Screw

Screw

Judith from SALEM, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven not reaching temperature

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Parts Used:

Oven Sensor

Marsha from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

You

Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.

Parts Used:

Vent Trim - White

Ron from CARIBOU, ME
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Paint peeling from strip

removed 3 screws holding the strip and replaced with new strip

Parts Used:

Range Trim Lower (White)

Myron from Punta Gorda, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dual burner would go to highn heat.

Watched video & did just guy in video did. Very easy job & the burner works like new.

Parts Used:

Infinite Control Switch, 6"

LOUIS C from GRAND JCT, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

chemical etching of black painted finish on drawer front panel

took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!

Parts Used:

Drawer Panel Front - Black

michael from mesa, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

temp level uneven

after watching the video, installed the temp sensor. Super easy

Parts Used:

Oven Sensor

Paul from HARMONY, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner did not always reduce heat when temp. Was lowered.

My husband unscrewed the bad switch and replaced with the new one.

Parts Used:

Infinite Switch - 8 Inch

Annie S from RIDGEVILLE, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the oven temperature was not working right. I installed a new oven sensor. Works get now

Watch the video...

Parts Used:

Oven Sensor

Rosalind from APOLLO, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light kept burning out instantly

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Parts Used:

SOCKT-LITE

David from ENID, OK
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drawer guides missingJust

Just follow included instructions.

Parts Used:

Drawer Glide Kit - Black

Mark from Killbuck, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

It break with the time

I order the part here, the first part never arrived, it was an empty package, the second part was breaking, the glass support was missing. Broken from the vent trim, then I was tired of it so I just put back the original broken part with some super glue on it, lol

Parts Used:

Vent Trim - (Black)

Julie from MARGATE, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

No heat in oven

Broiler worked, Oven did not.
Remove two Phillips screws, unplug element, reverse for installation.
Did not correct the issue.
After replacing the oven temperature control also, it turned out the control board was the issue all along.

Parts Used: