- Home
- ACR4303MFW3
- Instructions
ACR4303MFW3 Maytag Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Parts Came With No Instructions And We Couldn't Find Directions On Line.
-
Kathleen from Livingston, MT
- A Bit Difficult
- 1- 2 hours
We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got
... Read more
the parts, had them installed and saved over $800 on a new stove - well worth the effort.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Heating element would not get red hot
-
James from Lewisville, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.
Was this helpful?
Thank you for voting!
rusted drip bowl
-
kyle from Schwenksville, PA
- Really Easy
- Less than 15 mins
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Was this helpful?
Thank you for voting!
Two drip Bowls needed to be replaced
-
Robin from Boca Raton, FL
- Really Easy
- Less than 15 mins
No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!
Other Parts Used:
Was this helpful?
Thank you for voting!
Drawer Glide Snapped Off And Broke
-
PATRICIA from GEORGETOWN, MA
- Really Easy
- Less than 15 mins
Snapped in the new drawer glide. Took less than 5 minutes.
Was this helpful?
Thank you for voting!
Drip Bowl beyond cleaning
-
Ann from Memphis, TN
- Really Easy
- Less than 15 mins
Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!
Other Parts Used:
Was this helpful?
Thank you for voting!
corroded, rusted drip bowls
-
Noah from Richardson, TX
- Really Easy
- 15 - 30 mins
replace
Other Parts Used:
Was this helpful?
Thank you for voting!
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
-
Dave from Titusville, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this helpful?
Thank you for voting!
I had a power serge and it burned the Plug at the termial block and melted a few wire.
-
Robin from Vanderbilt, PA
- Really Easy
- 15 - 30 mins
-
Socket set
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this helpful?
Thank you for voting!
Left front 8 inch burner knob control stop regulating heat temprature.
-
Alfred from Ann Arbor, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I purchased a new infinite control switch 6". and replace the old one.
Was this helpful?
Thank you for voting!
Generic Drip Bowls Made The Burners Tilt.
-
PATRICIA*NAYLOR from NEW PRT RCHY, FL
- Really Easy
- Less than 15 mins
Pulled out the generics and popped in the correct bowls for my whirlpool. Done in less than 10 minutes and perfecto,. . . Level burners :-) thanks we'll be back when we need you again.
Other Parts Used:
Was this helpful?
Thank you for voting!
The burner didn't work because it had the wrong drip bowl
-
Leslie from Spring HIll, FL
- Really Easy
- Less than 15 mins
Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.
Was this helpful?
Thank you for voting!
Broken oven door handle due to pulling oven by handle.
-
Dennis from Colchester, VT
- Really Easy
- Less than 15 mins
-
Screw drivers
Warning: Door falls apart after removing the two screws which attach the handle. No big deal, just a suprise!
Was this helpful?
Thank you for voting!
bowls had burnt on food
-
David from Saranac Lake, NY
- Really Easy
- Less than 15 mins
replaced them
Other Parts Used:
Was this helpful?
Thank you for voting!
Drip plans needed replacement
-
Margaret from Vero Beach, FL
- Really Easy
- Less than 15 mins
Removed old ones replaced with new oned
Other Parts Used:
Was this helpful?
Thank you for voting!