My Orders
- Home
- ABL2227VES2
- Instructions
ABL2227VES2 Amana Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broke my original Kickplate Grille
3 of 4 people
found this instruction helpful.
-
Daniel from GEORGETOWN, TX
- Really Easy
- Less than 15 mins
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this helpful?
Thank you for voting!
Center Crisper rail
3 of 4 people
found this instruction helpful.
-
Richard from PASADENA, CA
- Really Easy
- Less than 15 mins
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
I purchased a display model that was missing a part.
3 of 4 people
found this instruction helpful.
-
Monte from Longview, WA
- Really Easy
- Less than 15 mins
Snapped on the new toe grille.
Was this helpful?
Thank you for voting!
Water not draining to pan. It caused an ice build up under the freezer draw
3 of 4 people
found this instruction helpful.
-
Rich from WINSTED, CT
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this helpful?
Thank you for voting!
I had a loose fitting old condensor fan blade on my new motor.
3 of 4 people
found this instruction helpful.
-
Roger from SMITHFIELD, RI
- Very Easy
- Less than 15 mins
-
Nutdriver
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a
... Read more
snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Read less
Was this helpful?
Thank you for voting!
The center rail was broken
2 of 2 people
found this instruction helpful.
-
Joella from THE DALLES, OR
- Very Easy
- Less than 15 mins
The part just snapped in. super easy.
Was this helpful?
Thank you for voting!
Ladder hooks broke
2 of 2 people
found this instruction helpful.
-
Miguel from ESCONDIDO, CA
- Very Easy
- Less than 15 mins
Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max
Was this helpful?
Thank you for voting!
Gasket not sealing good
2 of 2 people
found this instruction helpful.
-
Vince from Miami, FL
- Very Easy
- Less than 15 mins
Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 people
found this instruction helpful.
-
Gerald from COLORADO SPGS, CO
- Really Easy
- 30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 people
found this instruction helpful.
-
Brent from PRESCOTT, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver
Super simple following the instruction video you posted. Thanks!
Was this helpful?
Thank you for voting!
The old shelf shattered when we tried to clean it
2 of 2 people
found this instruction helpful.
-
Michael from COAL VALLEY, IL
- Easy
- 30 - 60 mins
Just slipped it in. I think it's a very poor design.
Was this helpful?
Thank you for voting!
Freezer cold ; fridge warm . Freezer not defrosting.
2 of 2 people
found this instruction helpful.
-
Tim from Oxford, MA
- Really Easy
- 1- 2 hours
-
Screw drivers
Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done
Was this helpful?
Thank you for voting!
the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!
2 of 2 people
found this instruction helpful.
-
Marc from SEASIDE, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper ... Read more ly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work proper ... Read more ly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..
Read less
Was this helpful?
Thank you for voting!