AAV7000AGW Admiral Washer - Instructions

For this repair the tub must stay centered in the machine. I used a shim between the tub and front panel. Tilt the front of the washing maching aginst a wall and brace if needed. Remove the belt and pully. To remove the stator, I replaced 3 of the 6 bolts with a 2" long bolt of the same thread (replace every other bolt). This is needed because the spring is under 100# pressure. Remove the 3 original blots and than the 3 2" bolts. Remove each of these three a little at a time. Install the new stator and brake rotor. Use the 2" bolts in the stator to compress the spring. Reinstall the the other 3 bolts, pully, and belt.

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

First, I disconnected the power cord then I removed the panel that held the knobs in place. Then I pulled the center holding clip, what holds the knob secure, with the screwdriver and the broken knob slipped right off. Then I put the new knob on the shaft and slid the holding clip on the backside of the panel. Lastly, I put the panel back and screwed it back down and that's all. Works like nothing ever happened.

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

I used a needle nose pliers to release the turning mechanism from the piece left broken on the timer. Once removed, I simply clicked on the replacemnet part. It was super simple. I love that I can do most things myself with the parts, and not have to pay the expense of hiring a repairman.

We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

unscrewed screw holding old actuater in and replaced it whith the new part.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!