A89L-4-R Admiral Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Electric surface burner would only turn very hot
-
Vittorio from Wakefield, MA
- Easy
- 15 - 30 mins
-
Screw drivers
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if
... Read more
I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Read less
Was this helpful?
Thank you for voting!
burners would not come on without moving them around
-
Ronald E. from Marissa, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type thi
... Read more
s but i am slow at typing
Read less
Was this helpful?
Thank you for voting!
Holes in the air filter of our Jenn-Air grill
-
Janice from Ocala, FL
- Really Easy
- Less than 15 mins
Simply pulled the old filter out and put the new filter in.
Was this helpful?
Thank you for voting!
Replacement
-
Barb from Holladay, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this helpful?
Thank you for voting!
Burner receptacle had malfunctioned and been removed
-
Kerry from Silverado, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!
Was this helpful?
Thank you for voting!
The original filter was decomposing each time I washed it
-
Sharon from Kenai, AK
- Really Easy
- Less than 15 mins
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
Was this helpful?
Thank you for voting!
surface burner stopped working. Was not heating up.
-
timothy from south bend, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call
... Read more
would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Read less
Was this helpful?
Thank you for voting!
Need new Surface Burner Knobs
-
Robert from Houston, TX
- Really Easy
- Less than 15 mins
Just pulled the old off and pushed the new ones on.
Was this helpful?
Thank you for voting!
Original burner switch fell apart
-
Jim from Addison, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring th
... Read more
e original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.
Read less
Was this helpful?
Thank you for voting!
plastic post for knob broke off
-
Graham from Bridgeville, CA
- Really Easy
- Less than 15 mins
I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of he
... Read more
r own plumbing and other household repairs. The repair took less that one minute.
Read less
Was this helpful?
Thank you for voting!
The surface burner element burned out on my 20 year old Jenn Air electric stove.
-
Wanda from Riverton, WY
- Really Easy
- Less than 15 mins
It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major
Was this helpful?
Thank you for voting!
replacement of heating element for elec. stove
-
Erica from Ivyland borough, PA
- Really Easy
- Less than 15 mins
plugged it in to the spot where missing element was.
Was this helpful?
Thank you for voting!
Filter worn out, exhasut fan kept going off
-
John from Cayce, SC
- Really Easy
- Less than 15 mins
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete
Was this helpful?
Thank you for voting!
Filter was very old and falling apart.
-
June S from San Antonio, TX
- Really Easy
- Less than 15 mins
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Was this helpful?
Thank you for voting!
Heat Errosion
-
Fred from Temple Terrace, FL
- Really Easy
- Less than 15 mins
Wife installed them, they just snap into place on the Rock Grate.
Was this helpful?
Thank you for voting!