9475XVB Magic Chef Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gas would come on, would not ignite. Oven not heating.
1 person
found this instruction helpful.
-
Karen from DAYTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the
... Read more
brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Read less
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people
found this instruction helpful.
-
Ben from Belen, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
Oven did not ignite
1 of 2 people
found this instruction helpful.
-
John from Racine, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..
Was this helpful?
Thank you for voting!
oven door seal
1 of 2 people
found this instruction helpful.
-
David from Jacksonville, FL
- Really Easy
- Less than 15 mins
easily pulled old seal out and push new seal in place simple and quick.
Was this helpful?
Thank you for voting!
Oven Ignitor went to ignitor heaven.
1 of 2 people
found this instruction helpful.
-
Brian from Pittsburgh, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I wou
... Read more
ld absolutely use your services again. Oven is back to working great! Thank you!
Read less
Was this helpful?
Thank you for voting!
Bottom oven burner wouldn't light.
1 of 2 people
found this instruction helpful.
-
James from Lino Lakes, MN
- Easy
- Less than 15 mins
-
Nutdriver
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
Was this helpful?
Thank you for voting!
Oven Wouldn't Light. Smell Of Gas Before Lighting
1 of 2 people
found this instruction helpful.
-
Charles from Alexandria, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I went online to find out about the availability of the part. In my search, I found what others had experienced and how they repaired it. Second, I ordered the part and followed others stories on their repair efforts. Third, I unplugged the range and removed the racks. Fourth, I removed the bottom of the oven which lifts out bac
... Read more
k first. Fifth, I removed the wing nut securing the flame difusser making it easier to access the element. Sixth, I had read that others had problems saving the original screws and/or threaded holes. I sprayed some wd-40 on both screws. They came out and back in without a hitch. Seventh, I removed and replaced the element, snap out, snap in. Eighth, I turned on the oven. It took about 15 seconds to glow but wow, it lit 5 seconds after that. I am my wife's hero!
Read less
Was this helpful?
Thank you for voting!
Oven ignitor would glow but took 30 - 40 mins to heat
1 of 2 people
found this instruction helpful.
-
Catherine from Newton, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!
Was this helpful?
Thank you for voting!
Oven wouldn't heat. Igniter was broken.
1 of 2 people
found this instruction helpful.
-
Thomas from Allison Park, PA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 of 2 people
found this instruction helpful.
-
michael from newhall, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ... Read more ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, y ... Read more ou will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.
Read less
Was this helpful?
Thank you for voting!
oven would not light , smell of gas
1 of 2 people
found this instruction helpful.
-
jerry from staten island, NY
- Easy
- 15 - 30 mins
-
Screw drivers
removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com
Was this helpful?
Thank you for voting!
smell gas and sometimes a whoof on ignition
1 of 2 people
found this instruction helpful.
-
Maynard from Knox, IN
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .
Was this helpful?
Thank you for voting!
The broiler would not lite at all and the oven would lite occasionally but would not maintain temperature.
1 of 2 people
found this instruction helpful.
-
Vincent from Lewes, DE
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I replaced the igniter in both the oven and the broiler. This was my first time ever working on a range.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket ... Read more wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.
To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.
I removed the oven door for easy access. To replace the oven igniter, I took the bottom floor out of the oven. The igniter is readily visible at the rear of the burner. I removed the two screws holding the igniter with a socket ... Read more wrench. The screws were somewhat stubborn but yielded rather quickly. I gently pulled the two wires attached to the igniter from the back of the oven until the connector was exposed. I disconnected the old igniter and connected the new one. Then I simply reversed the the procedure, tucking the connector and wire back through the hole it came from and re - installed the two screws in the bracket. The insulation provided with the kit was used to plug the hole in the back of the oven.
To replace the broiler igniter, I essentially followed the same procedure. However, I chose not to remove the broiler baffle. This made it more difficult to both remove and re-install the two screws holding the ignitor. Otherwise, everything else went smoothly. If I had to do it again, I'd remove the baffle.
Read less
Was this helpful?
Thank you for voting!
oven would not light
1 of 2 people
found this instruction helpful.
-
mark from fredericksburg, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
replaced the igniter in oven
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven would'nt heat
1 of 2 people
found this instruction helpful.
-
Ariel from Oxford, NJ
- Easy
- 15 - 30 mins
-
Nutdriver
First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven wo ... Read more rked perfectly
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven wo ... Read more rked perfectly
Read less
Was this helpful?
Thank you for voting!