919167621 Craftsman Compressor - Parts

It is a genuine item that is supplied directly from the original equipment manufacturer for use with air compressors. This is an identical replacement for a missing or a faulty cover for the pressure switch, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. It i...Read mores a high-quality part which is made of durable plastic and is sold individually, keep in mind it includes the plastic cover with a red knob. Note, the switch itself is sold separately.

This genuine DeWalt carbon brush is designed for use with select compact routers and includes a wire lead enclosed in a protective rubber sheath. It’s an exact replacement part sourced from the original manufacturer, ensuring a proper fit and reliable performance. The brush measures approximately 0.45 inches long, 0.25 inches wide, and 0....Read more20 inches thick. Carbon brushes are wear-and-tear parts that gradually wear down with use. When they do, your tool may lose power, run intermittently, or stop working altogether. Replacing them can restore full motor performance and electric braking. This part is sold individually, and since most tools use two brushes, it’s a good idea to inspect and replace both at the same time. Look for signs of wear like cracks, burn marks, or the brush being worn down near the wire. While replacing, also check the motor’s armature for any damage that could point to a bigger issue. Always refer to your tool’s manual to confirm compatibility.

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with air compressors. The hex head screw is used to secure the motor assembly to the bracket on the tank of the compressor. These screws are sold in packs of eight pieces and the packs are sold individually.

When using an air compressor, moisture naturally builds up inside the tank as air is compressed. If this water isn’t drained regularly, it can lead to internal rust and damage over time. That’s where the drain valve comes in—it allows you to release the built-up water and keep your tank in good condition. Located at the bottom of the tank...Read more, this valve should be opened after each use to prevent corrosion and extend the life of your compressor. If you tend to leave air in the tank for long periods, water accumulation can be even more significant. This replacement drain valve features a thread size of 18 TPI and is sold individually. Regular maintenance with a working drain valve helps ensure safe and efficient compressor operation.

This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic part that is intended to be used with air compressors from Porter Cable, Black & Decker, and Bostitch. This safety valve attaches to the switch box or the manifold, and is used to release air from the tank if the pressure becomes too high inside the tank. If the safety valve goes off it will need to be replaced, because it can not be reused. The safety valve is sold individually.

This is a genuine replacement part sourced from the original manufacturer for use with air compressors and generators. The flanged hex head bolt is used with several different types of equipment and the application of the screw can vary based on the model of the machine. This item is available as an individual replacement part.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

The gauge attaches to the pressure switch and is made of plastic and metal. It is an authentic OEM sourced item which is specially produced for use with compressors made by Porter Cable, DeVilbiss, and Black & Decker. This item is available as an individual replacement part. A wrench set may be helpful when replacing this part. This item may stop working and will need to be replaced.