9122XUB Magic Chef Wall Oven - Instructions

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.

was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They included a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.

Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

2 screws easy to remove and plug in the wire. job done.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

snaped them into oven cavity attached temp bulb job complete

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!