91193508991 Kenmore Range - Instructions

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

took out a couple of screws and replaced with new switch, plugged in switch wires. very easy

very easy and clean.

Ordered the part, it arrived and 5 minutes later it a complete installation

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Took back off and replaced.

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

Followed directions given by previous customers problems which we found on the internet.

I removed the door by unclipping the hinges with a screwdriver - very easy. I laid the door on the kitchen island unit on the polystryrene packaging. I removed all of the star bolts. I need not have removed the star bolts around the door hinges as these hold the hinges to the inner frame. The cracked double glazed unit lifted out and was replaced very easily. We took the opportunity to clean all of the parts that don't usually get cleaned - hence the time taken. Reassembly and reattaching the door was very easy. We didn't rush and were very careful in laying the door on a good flat surface. The oven is now good as new. Well done PartSelect for stocking such an old part - $125 to keep the range working perfectly.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.

I'm so pleased with the ease of placing my order, the price, and the speed of delivery. My only challenge was figuring out the correct part to order, as I didn't have an owner's manual for the range when we moved into the house. But once I located the model # in the range's lower drawer, the website did a good job of guiding me toward the correct replacement part. In my case there was no "repair" involved; I was simply replacing a broken lower oven rack. I would definitely use this company again.