Models > 91193508990 > Instructions

91193508990 Kenmore Range - Instructions

All Instructions for the 91193508990
76 - 90 of 128
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Drip Pans on Stove Top
Just removed the old drip pans and then inserted new ones...pretty dog gone easy!
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Shawn from Lubbock, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change out burner bowls
Took out the old ones and replaced with the new ones. Very simple task. It didn't take 5 minutes.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Carolee from Carson City, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner didn't work, using a test light showed only one side was hot.
took the back panel off the range, took the 2 screws holding the switch in place, took the old switch out, marked the wires took the wires off and clipped them onto the new switch, put the new switch into the switch plate, replaced the screws put on the knob, put the panel back on the range. rolled the range back into it's place. turned the buner on to check if it worked. It did so we were done.
Parts Used:
Surface Burner Switch - 8 Inch - 2500W
  • Kathleen M from Nampa, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace old burner bowls
It was easy to just replace the old burner bowls rather than try to clean them. The peices ordered from Parts Select were a perfect match and they arrived on a timely basis.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Daniel J. from Vernon, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original drip pans scrubbed so much-rusted....
Took out the original drip pans and set in replacements which I ordered in black enamel.
Slipped right in and look great as the oven door glass is also black. Look like they came with the range.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Jane from Quarryville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
eye wouldnt come on
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Parts Used:
Range Surface Element Control Switch - 6 Inch - 1560 W
  • daniel from valentines, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Incorrect Burner Bowls
For 12 years I've been suffering with the incorrect burner bowls...I love to cook and it's really irritating when your bowls don't fit correctly. Now, I am amazed at how my burners fit! Thank you! What a Blessing!
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Valerie from Corvallis, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stove's burner bowls were dirty and old and the chrome was gone where the cooking drippings had collected under the previous owner's usage.
We simply typed in the model of the range and several selections of replacements came up on your website. We ordered the black porcelain ones to replace the old chrome ones, thinking they might hold up better and be easier to clean. They look great and I really think they WILL be easy to wipe up. Thank you, Part Select! Patty in Indiana
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Patty A from Noblesville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
Parts Used:
Range Surface Element Control Switch - 6 Inch - 1560 W
  • bryan from cocoa, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner not heating.
Isolated to control switch.

Replaced
Parts Used:
Range Surface Element Control Switch - 6 Inch - 1560 W
  • Jack from Greensboro, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had bad surface element on electric stove top
Replaced the old element with the new part with a problem.
Parts Used:
Surface Element - 8 Inch
  • Ralph from Hendersonville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner bowls were encrusted with grease and spills.
I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Ed from Canyon City, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
temperature sensor went
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Parts Used:
Temperature Sensor Kit
  • Alex R from Randoff, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The burner combusted burning the the burner switch
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Parts Used:
Surface Burner Switch - 8 Inch - 2500W
  • Felipe from Donna, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Switch would not adjust temperature
Simple; unplug stove, take back cover plate off. Pull off front knob. Remove screws holding in switch.Replace wires one at a time to avoid dis-connections - or make color coded diagram. put back together. DONE
Parts Used:
Surface Burner Switch - 6 Inch - 1500W
  • William from Roanoke, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 91193508990
76 - 90 of 128
Back to Top