All Installation Instructions for Kenmore Microwave Oven Combo 91141485992

Needed to replace missing trim

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.

Parts Used:

Outer Bottom Trim

Jennifer from Castaic, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

While on self clean, the bake element began to burn

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I plugged in the new element and proceeded to clean the oven which is what I was doing when the problem occured.

Parts Used:

Bake Element - 3400W

Scott from Troy, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

No heat

Replace the fuses

Parts Used:

Microwave Fuse

Edwin from New York, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

No heat.

Replaced the fuse. Result; did not fix the problem.

Parts Used:

Microwave Fuse

Mack from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Missing oven rack

I opened oven and pushed oven rack inside.

Parts Used:

Oven Rack

Damaris from Easton, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

no racks to oven

Easily glide in.

Parts Used:

Oven Rack

Johnette from Baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Heating Element

Removed two screws, removed two wires, installed new element. So easy a caveman could do it.

Parts Used:

Bake Element - 3400W

Bradley from Perryville, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Lower heat element burned out

Very easy, only small issue was the holes for the two self taping screws were a bit high, so I had to drill two new holes to complete repair... Still a very simple repair.

Parts Used:

Bake Element - 3400W

michael from marstons mills, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Broiler element fails to heat

Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.

Parts Used:

Broil Element

Stanley from Bethesda, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Heating element was fried.

Remove 2 nuts attaching element to oven. Pull element out 1" to 2" exposing electrical leads. Pull leads off old element. Replace with new. Toughest part is seeing the elements in a dark oven. Have a light handy.

Parts Used:

Bake Element - 3400W

Roger from Cranberry Twp, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set

Was this instruction helpful to you?

Gasket worn and needed to be replaced

I simply removed the old one and installed then new one. No special tools needed.

Parts Used:

GASKET OVEN Door

Thomas from Loveland, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Parts Used:

Oven Rack

Vicki from Irvine, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven Sensor Replacement

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

Parts Used: