91141086991 Kenmore Wall Oven - Instructions

Disconnected power, removed two screws from bracket. Unplugged old element, installed new element and replaced screws in bracket. Restored power and back in business!

Turned off the oven power at the breaker. Removed the oven door by opening it all the way down. Flip the two metal tabs, one on each side, so the door releases. I used a flathead screwdriver to do it. Close door almost all the way and lift up to remove. Once the door is removed, there are two screws in the back of the oven connected to the heating element. Unscrew both screws. Gently pull out the heating element from the back wall. There are two terminals connected to wire clips holding the wiring in the back. disconnect, both terminals from the wire clips. Be careful not to pull on the wire or pull out from the wall too far. Connect to the new heating element to the same wire clips gently push it back into the wall reattached the two screws, reattached the door and turn on the breaker and test the heating element. I used YouTube to figure out how to disconnect and reconnect the door so that is an option.

Removed element. Ordered new one. Installed it.

Replaced new light housing.
Thanks to you guys for the prompt response

Removed old element with a socket wrench. Replaced new element with socket wrench. Pretty easy!

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.

basically unscrew two screws, unplug, plug new one in and screw the screws back in.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I plugged in the new element and proceeded to clean the oven which is what I was doing when the problem occured.

Before you get started on this be sure that you already have the Bottom Cabinet Trim Assembly (item #PS952490) either ordered or installed. We were not aware that you had to order both trim items separately which meant we had to remove the oven door twice. Using the screwdriver to pull back the door tabs, we first removed the oven door. The trim installed very easy. We just lined up the holes, pushed in, and then down on the trim to lock it in place. When reinstalling the oven door, be sure that door latches are almost fully extended before reinserting them into their slots.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.

nothing to it.

Remove 2 nuts attaching element to oven. Pull element out 1" to 2" exposing electrical leads. Pull leads off old element. Replace with new. Toughest part is seeing the elements in a dark oven. Have a light handy.

I simply removed the old one and installed then new one. No special tools needed.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.