91141069690 Kenmore Wall Oven - Instructions

Feedback on site warned me that broiler element is only connected to oven wiring with press-on spade lugs rather than screws. Even with care I managed to 'lose' a wire and had to retrieve it with section of stiff coat-hanger wire bent into a hook. Coming off that experience, I soldered the spade terminals together before reassembly to avoid a repeat. New element, however, failed to rectify problem. Professional technician found main control unit defective -- a $300 part including installation, but at least GE still has it available. My advice to others in this situation is to remove old element before ordering a replacement, and test with meter to see if it's defective. It may or may not be worth going beyond an element replacement to you.

Removed oven from cabinet and replaced oven control board, door lock was included in package,installed it also, installed new limit sensors. removing the connections from the old control and putting them on the new one was a little difficult, just have to be gental,plyers worked well, the new control had revised selonids that had 4 terminals and I only had 2 wires, one for bake and one for broil, the selonids had paint dots to show you which ternimal to hook the wires to, yellow on bake and violet on the broil, Lb1 had a stamp on the circuit board next to the side ternimal, the other two ternimals were blank for me. It would be real nice if a diagram was included, even after contacting GE answer center and requesting a diagram, they only had the orginal print that came with the stove, revised the board and not the blueprints, see how that works, call a tech to hook up 2 wires. Put oven back in cabinet and no more error codes.

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

just slipped it in

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

nothing to it.

placed them in propper position we had been to apliance stores and told they would need to order them and it may take up to two weeks to get them. we ordered them from you and they were here in a matter of days, and the price was the best we had been quoted. thank you so much

I carefully opened the oven door and slid the rack into the groove taking great care not to dislodge the heating element nor to burn myself on the cold oven door. I then pulled open the drawer on the oven and, again, with great care placed the broiler pan into the drawer and slid the drawer closed, again taking great pains to make sure I did not burn myself on the cold over. The reason for the length of repair time is I did not open the box for 2 days. Thanks for the laugh!!!!!!!!!!

I opened oven and pushed oven rack inside.

1. Switch electricity off at circuit breaker panel. 2. With a helper slide door off hinges and set aside. 3. Remove all oven racks. 4. Using socket wrench remove the two screws attaching element to back of stove. 5. Pull the element from the back of the stove and slide off the 2 electric bayonet clips from the old element. 6. Install new element attaching the new element to the old electrical clips. Note: You may have to crimp down the clips to keep them secure to the new element. 7. Reinstall element screws to back of stove using nutdriver. 8. Insert racks and slide door back onto hinges. 9. Turn back on electricity. 10. Turn on element and let it "burn in" for a few minutes. Note: There will be a slight smell while doing this.

Easily glide in.

removed twoscrews from rear of oven,undid two spade connections removed element.replaced with new one,thats it.

Removed oven from wall. Door slides up and off, and 4 screws into cabinet removed, and oven slides right out onto a coulple kitchen chairs positioned to support the oven. 1 man job to lift. Used nutdriver to remove metal cover on bottom back of oven to expose the slide on electrical connection. Used nutdriver to remove old bake element and install new bake element. Reconnected electrical wires, reinstalled back cover, and then reinstalled oven into cabinet. I actually removed the internal metal cover over the convection fan and element also but probably didn't need to do that to remove and install the new bake element.

I found that some of the wires were hard to remove, so I had to use a pliers. When it came time to install the new part, I found it easier to mark the wires by color on a piece of paper and their location from right to left as I was looking at it. To me it was to hard to try to hang on the panel and try to plug the wires into the new part.

After securing the power, removed wires one at a time and placed them in the new controller. The new unit was slightly different at a couple connectors but both old and new boards were marked with alphanumerics and or colors.