91136665892 Kenmore Range - Instructions

After reading the other DIY's directions, we explored how to remove oven door. When the part came in, my sister who was visiting, removed the oven door (30seconds), removed bottom drawer (30 seconds), noted where spring was attached, took off screws and spring, installed new hinge with roller, took a minute to decide if the new hinge came through the back or the front (front), she reattached the spring and screws. Put door back on and then struggles to put the drawer back into place. Total time less than 5 mintues, most time spent on returning bottom drawer to its home. Thanks part select for helping me not burn my self every time I try and get food out of the oven!!! I open the oven door all the way and am so delighted!!

Followed the instructions

The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best

Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.

The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again

Removed front oven door, pull out bottom drawer and top burner glass panel to reduce weight. Pulled out from cabinet, shut off gas, removed gas line, removed two output gas lines from gas regulator, removed gas regulator, removed input pipe fitting from old gas regulator and installed it on new regulator using pipe compound on threads, installed gas regulator on stove, attached two output gas lines to new gas valve, attached gas line, checked for leaks, and then installed Top, front door and lower drawer, done. 2-3 hours.

After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

the broiler would light once in awhile and it appeared that the igniter was working. But it wouldn't let enough current through to open the gas valve. The nuts holding it on broke off but drilling them out and replacing with two sheet metal screws worked ok. Don't know how that will hold up to the heat though. The wiring was easy to connect ( wire nuts) but the lead wires from the stove are not that long so all the operation had to be done way in the back of the oven enclosure.

Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.

The left door hinge was broken. There are three screws that hold the hinge. It is very easy to take it out and put the replacement in

Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.

I really can't add much more to the very good instructions already posted. You will need a flashlight to see the spring -- when connected it stands vertical with one end connected to the hinge. There are 3 holes you can connect to -- I used the middle one, #2. The other end of the spring is anchored to a hole/slot in the stove frame. It is very easy to position this spring. Be careful though, there's a lot of sharp sheet metal in there. You will need a phillips head screwdriver to remove/install 3 sheet metal screws that fasten the hinge to the stove.

Slid door off hinges. Removed 3 screws which hold hinge in place. Removed drawer to access spring for hinge. Gasped at all the crumbs and crap which had collected underneath the drawer. Cleaned up crumbs+crap from floor. Disconnected spring from hinge and removed old hinge completely. Installed new hinge with 3 screws. Attached spring to hinge - center hole fitting. Slid drawer back in place. Angled hinges outward in order to re-install door. Slid door back onto hinges. Door now operates nice and smoothly. Job well done.

I removed the door by pulling it up (according to the instructions). Than took a philips screwdriver and
removed the three screws in each hinge, unhooked the springs
and slid the old hinges out of the slots.
The new hinges slid into the slots perfectly so the screws
were installed, the springs rehooked and the door installed.
Real simple.