Models > 91133203101 > Instructions

91133203101 Kenmore Cooktop - Instructions

All Instructions for the 91133203101
16 - 30 of 37
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner injet replacement
I needed a right front burner injet which is no longer made. On my cooktop I was able to move the left burner to the right and then ordered the left. Very easy to replace.
Parts Used:
BURNER INJET-LT. Front
  • Edward from NEPTUNE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniters would not turn off
Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
Parts Used:
Spark Igniter Switch and Harness Assembly Spark Module - (4+0)
  • Paul from UPLAND, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing ignitor
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
Parts Used:
Spark Igniter
  • Sam from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Parts Used:
Grate Foot
  • Gary from HENDERSONVLLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Parts Used:
Top Electrode Mounting Clip
  • Dana from LEEDS, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Parts Used:
Spark Module - (4+0)
  • paul from las vegas, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
very easy
there were no grate pads so it was easy to add them.
Parts Used:
Grate Foot
  • ROBERT from CYPRESS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Grate foot is to big for the hole.
I had to drill the hole to a larger size to enable the foot to fit.
Parts Used:
Grate Foot
  • Harold from Broadalbin, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
Nothing technical.
Parts Used:
Grate Foot
  • Chelagh from Fredericksburg, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
Used scribe to remove grate foot plug still in grate inserted new foot.
Parts Used:
Grate Foot
  • John from Tijeras, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Parts Used:
Grate Foot
  • Gene from Simi Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Parts Used:
Spark Module - (4+0)
  • Douglas from Knoxville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fan knob was loose due to the metal insert being missing
Removed the knob and replaced it with the new knob. Didn't even break a sweat!
Parts Used:
Selector Knob
  • Maurice from Grand River, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
one of the 4 burners wasn't sparking
I used a hex wrench to remove the 8 screws ( 2 on each burner ), pulled up the knobs, and lifted the ceramic top. use pliers to disconnect the spark plugs. I disconnected the switch harness from the igniter, disconnect the igniter wires remembering the color scheme.My igniter had a minor variance from the old one which an acompanying map clarified. I installed the new switch harness and the new igniter, made the igniter connections according to the color scheme and the accompanying diagram, replaced the ceramic top, pulled spark wires thru, installed the burners and the spark plugs, tightened the 8 screws, and tested the burners.
Parts Used:
Spark Igniter Switch and Harness Assembly Spark Module - (4+0) Burner Gasket Spark Igniter Burner Gasket
  • Arthur from Bloomingdale, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Missing grate foot.
Ordered by phone parts & very pleased with all of transaction.
Parts Used:
Grate Foot
  • Barbara J from Sweetwater, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 91133203101
16 - 30 of 37
Back to Top