7WRS22FEBF00 Whirlpool Refrigerator - Instructions

I began by replacing the central light board by using a plastic non-marring wedge type tool slipping it between the housing and the retainers to release the latch like catch. Then I removed the lightboard and light cover assembly by depressing the latch like retainers for the two wire connectors. Installation was as simple as snapping the wires into the connectors and then pushing the lightboard and light cover assembly into place. One major note: I learned from a repairman that you cannot resolve the problem by simply replacing the central lightboard. you must replace all three lightboards, the two in the refrigerator and the one in the freezer because unless you can absolutely identify which board is causing the fault, it will continue to cause a problem on the main board and the lights will not work. Replacing the other two boards is the same as the central board. Additional comment to consider: I absolutely fail top see how this design of using three circuit boards for a simple light saves me anything; in fact after only 5 years it has cost me in excess of $400 (or 20% of the original cost of the unit) just in materials for a simple light--absurd, ridiculous design. If it burns out again I will have an appliance repairman install a simple 1950's design switch a small LED bulb which will probably last longer than the unit.

When the filter arrived, I removed it from the package.
Upon reading the instructions, I removed the old filter.
When I removed the old filter I NOTICED HOW IT CAME
OUT SO THAT I COULD HOLD THE NEW FILTER IN
THE SAME POSITION AND REPLACED IT WITH THE
NEW IN THE SAME POSITION. When I closed the cover
door, I went to the display panel and reset water filter display.

I was not able to unplug the refrigerator because it is housed in a built-in. I removed the icemaker and following simple instructions from YouTube was able to pry the cover off the existing part. After a few gentle tugs, I disconnected the pinned wires from the old part. Connecting the new part was a little tricky but I managed with a little contorting. As soon as the pins connected the freezer light as well as the refrig lights came on. It took about 15 minutes to complete.

I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.

I tried to replace the light in the fridge first but couldn’t get it out (that one has the control board and is very expensive) so a replaced the one in the freezer by prying it off the ceiling. When I plugged the new one in all the other lights came on full power. Strange but I sent the other one back.

Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!

Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.

When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)

On a side by side refer, you need both doors open to unscrew the three 1/4 inch screws,
1. Remove the ice tray
2.the ice arm needs to be in the up position, so no water will flow while dissembling.
3. Remove the two top screws,
4. While holding the ice maker with o e hand, remove the bottom screw.
Balance the ice maker and unplug the ice make electric plug in the rear of the ice maker.
5. Take the I e maker out.
6. The ice maker does not come with the ice arm, so you need to remove the arm from the old or broken ice maker and install it in the new ice maker.
7. Resemble in reverse order.

I did not unplug the refer from the wall socket, you may want to do this. It recommended but I did not.
There you go.

Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.