7MMGDB950AG0 Maytag Dryer - Instructions

The repair was easy. Shut off all power to the range, or unplug it. Remove the sheet metal back from the control panel using a nut driver or socket set. Pull the knob from the front of the control panel. Remove the two Phillips head screws that were hidden behind the knob. Pull the control switch out the back side of the control panel. Compare the old switch with the new one, to make absolutely sure you have the correct switch. Remove one wire at a time from the old switch and immediately install it in the exact same position on the new switch. When you have successfully transferred all of the wires from the old switch to the new switch, reinstall the new switch using the two Phillips screws. Reinstall the knob and the sheet metal cover. Plug the range back in, and/or turn the power back on. Trying boiling a pan of water to confirm that the repair resolved the issue.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Remove old filter
Vacuum out
Install new filter

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.

The repair cost us less than $9.00 and about 1 minute to repair. You can only imagine how much a tech would have charged us!! We are so very happy that we discovered this site . The instruction video they offered, the customer service via their website AND quick delivery of the part, has insured them that we will be repeat customers. Thanks so much !!!!! Bravo! Annie & Peter in , Nevada

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I thought it had to be the igniter so I replaced that part. The dryer still did not start. I replaced the high limit and hoorah dryer works. Two weeks go by, the dryer is drying the clothes but my wife smells gas in the laundry room. I replaced the coil pak on the gas valve. My wife says she still smells gas. I replaced the radiant flame sensor and no gas smell for 2 weeks now.

I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.