79641372211 Kenmore Washer - Instructions

Ordered and replaced the hot and cold inlet valves - followed the instructions off of the video posted on the Part Select website ... completed the repair in less than 10 minutes

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

Removed and replaced unit after turning off the cold water valve. Turned water back on and it worked as it should. I also have to mention the very rapid shipping! Thank you!

Replaced it

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.

Did some research and found this video on YouTube. I would not have attempted the repair without out! https://www.youtube.com/watch?v=MNp1hzlcF1g

I looked at the video that is on the partselect.com website. The person that I talked to from the website was very knowledgeable about the problem with my washer and he gave me the part number to type in the search box of the website. When I typed the part number in the search box the part showed up and the installation video showed up also. The video is an excellent video. It shows exactly how to do it. I also downloaded the operator manual from the website to look up what the error code meant.

Viewed two (2) on-line video's for bearing replacement. Produced a 40 item "punch list" as to action to perform following video. Followed sequencing of video's. Noted a 10mm and 17 mm socket needed, used 3/8 drive sockets. Also noted that a "deep Socket" of unspecified size used to aid in removal of nylon pins attaching (3) shock absorbers. Found that 1/2 inch sized (SAE) socket in my 1/2 inch drive socket set fit in the confined space nicely. Did not need the "deep sockets" (3 plus inch overall length) rather a normal sized 1/2 drive socket worked nicely to depress the nylon pin retainers. During reassemble replaced outer tub gasket, checked bolt torque six (6) times over 45 min. to assure complete seating.

Followed the video instructions provided.

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.