79092649810 Kenmore Range - Instructions

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

Drawer glide came off oven drawer. Wish I had taken old part off and inspected more closely. I thought tab had broke off. Turns out these glides are made of steel and very robust. However the drawer is soft sheet metal. I took off the old glide and turned out it was fine. Tab just popped out. But there was a burr on drawer i had to file off to get back on. So my advice is take old glide off first and inspect carefully.

Started with trying to take the door off for easier access to heating element.

I ended up lifting the door off and the front glass shattered and I sliced my hand open.

Ended up buying a new oven/range.

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

Went online to find replacement rack. Didn't want to spend the money for a rack I didn't like. Besides the range is 11 years old. Still in great shape. Opted for the simple oven rack.
Open the box and place in oven. Wah lah..
Thank you partselect.com

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)

Unscrew two very visible screws located in the back of the oven holding in the panel. Remove panel. Install new panel. Replace screws. Could have used new screws but didn’t have any.

I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be

1) First things first. Either turn off the Circuit breaker, or unplug oven.
2) Remove two screws under oven door that holds the glass top.
3) lift up the glass top, prop it with the 18” board, and place blanket between glass top and oven.
4) Remove two screws of the bracket that hold the two burners.
5) use tour phone camera to take pictures of where the colored wires go on the heating element.
6) use needle nose pliers to pinch, and push out the heating element from the bracket.
7) Remove the wires from the heating element, and the three brackets.
8) Place the three brackets onto the new heating element at the same hole location as the were on the old one.
9) Press the new heating element in the main holding bracket.
10) Place the wires on the correct terminals of the heating element. Note: the camera phone pictures work perfect for this.
11) Raise the two burners attached to the bracket up, and attach the two screws holding this bracket back up under the glass top.
12) Remove the blanket, board, and lower the glass top into place.
13) Open the oven door, and place the two screws back into place that is holding the glass top.
14) Turn the power back on and test.

Note: Other things to consider is you want to have the help of a helper while doing this procedure. The more hands you have holding things the better. There are YouTube videos on installing oven heating elements.

Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue

Easy watched on line video