79079019100 Kenmore Range - Instructions

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good qualit ... Read more y wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju ... Read more st the spark module for the burner.

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed whi ... Read more ch has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

Once I recieved the new part it was easy to determine what two screws to remove to remove both the panel and the handle. I removed the two screws, slid the panel up and removed it. The new panel locked into place when slid down over the door and I replaced the sctews.

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arri ... Read more ved early than anticipated.

take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.

Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.

removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since

pulled drawer out and took old igniter off and replaced it