79073433313 Kenmore Range - Instructions

Unplug the range, remove racks. Remove 2 screws from the bottom back corners ( this was the hardest part. I used a stubby screwdriver, but a longer one would be better. They are fairly long screws). Remove oven bottom, lifting from the rear. Remove burner cover. Bottom left corner is a triangle cover. Remove this too. Remove the 2 screws holding the old igniter in place. The igniter unplugs easily. ( I used pliers, the plug has a clip, and pliers grip better.) Install new igniter ( it only fits in one way ) reinstall mounting screws and covers. Replace oven bottom. (I didn't replace the 2 screws. The bottom sits solidly, and they are a bit of a pain.) Plug in, set clock, test for oven to fire up.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

It was a replace racks not repair. No problem

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Open oven door and remove metal splash plate on bottom of oven by removing two screws in back.
Remove heat distribution plate (metal) by unscrewing a single nut with pliers.
Now the ignitor is visible. Unscrew old ignitor by backing off two screws.
Detach the wires and reattach to new ignitor. (a cover plate may have to unbolt from the left back corner to get at one of the wiring connections.)
Reattach new ignitor and then flame distribution plate.
Put on splash cover and tighten back screws.
Test oven, it should light within 1 minute.
All is done.

First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the power and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.

1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.

2. If possible, remove the storage drawer for ease of access.

3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.

4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.

5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.

6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.

7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.

8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.

9. Reattach the drawer if necessary and plug the range back in.

10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.

remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble