79071054404 Kenmore Range - Instructions

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

I repaired with the use of 1 Phillips & 1 flathead screwdriver. It was very easy.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

Easy as pie. I had the new part in my hands in less than 48 hours. Fortunately for me it was a simple fix and I was literally cooking in under 15 minutes. I was a little worried about doing anything to a gas stove, but by looking at the other unbroken side, it was just a matter of snapping together a new assembly. What a wonderful website!

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

1)First unplug range.
On inside of oven, there's a copper, pen-like object connected to a copper wire. 2)Open the clips on side of oven that hold the pen-like object(the probe.)
3)Open the lid of the stove. On left hand side, there's a hole through which to pull the copper wire and probe out of the stove. Or you can just as easily use wire cutters to cut off probe and just pull wire from the oven through the hole. 4)Pull off the oven's thermostat control knob. Using screwdriver, unscrew both screws under where the knob was. 5)Now pull the flat wire connecters from both sides of the old thermostat. Remember which wire goes on which side.
6)Remove old thermostat and copper wire that's connected to it.
Replace thermostat. 7)Feed copper wire with probe through hole on left side of stove.
8)Slide flat wire connecters onto sides of new thermostat. Replace screws. Insert new probe into clips on side of oven. Close stove cover. Replace thermostat control knob. Plug in range. Test thermostat. 9)According to owner's manual, turn oven to 350° and oven should be no more than 50° above setting.

Need the thermostat now

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back together. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.