79070301703 Kenmore Range - Instructions

Very simple with instructions supplied, Removed two screws inside on back of door, then removed four more screws to get to inner glass,removed broken glass installed new glass, replaced all screws.Job completed. very good instructions,Thank You.

took screws on outer sides and then removed glass put in new glass replaced screws done

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

I just installed the extra rack and re-arranged the existing ones. Works great!

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

simple to unscrew the door handle from the inside, remove the broken trim, place new trim on, clamp the door together, then screw the handle back on. Went well!

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)

Removed the old oven racks and put in the new ones.

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.