79049602314 Kenmore Microwave - Instructions

Plastic trim on inside of the door pops out if you pry with a flathead screwdriver. Then lift door latch out of place and carefully remove the spring. New latch goes back in the way the old one came out. Door trim pops back in.

on the back side of the wall oven the sensor wire was ziptied tight. we had to totally pull oven out of its wall space, remove back panel, unhook zip tie, feed through sensor hole around insulation, connect and then replace back and return and relevel the oven. I have

This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the ... Read more relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.

First, I shut the OFF the main breaker. Then, I removed 2 screws holding the thermostat inside the oven. The wiring harness was too short to pull through small opening. I tried to fish the wires out with a piece of wire, but no luck. Eventually, the wiring harness disconnected and I had no choice but to remove entire wall oven from wall c ... Read more avity.

Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w ... Read more ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.

If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damage ... Read more d screw and then installed the replacement. Wish all appliance repairs were this easy!

Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch

I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply ... Read more on my ice maker.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.