79046572400 Kenmore Range - Instructions

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Tilted the surface unit and proped it up with the metal arm then I unpluged the old 8"-surface element and replaced it with the new 8"-surface element that I purchased from PartSelect.com. I then lowered the surface unit turned the burner knob on and everything worked fine. Thanks PartSelect.com.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Very easy to repair! I removed the old burner and slid the new burner element in its place. It was as simple as that! No tools required. My one and only complaint would be that the old burner was slightly larger (within 1 inch or so) than the new one so the new one sits slightly crooked on the stove top. But it works just fine. The item also shipped very quickly. Within a day or two. I am very satisfied with the transaction overall.

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Easy as 1-2-3

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

This repair was easy, but I would not have even tried if I hadn't read the tips from other DIYers - thanks! The website questions and schematic along with some common sense testing isolated the problem with the oven only heating up to 250 degrees. Since the broiler (upper element) worked ok, that made it likely that the temperature sensor was not the problem. That made almost certain that the bake (cooking) element was the problem. So, I ordered the part, which was delivered quickly. Early on the morning of the scheduled delivery date, I turned off the oven power at the fuse box and pulled the oven away from the wall. There were only 4 screws to remove in order to take off the rear panel. The bake element was attached to two slide-on connectors, one of which looked charred and partially disconnected. I cleaned the charred connector, reattached it to the bake element, turned the power back on, and then turned the oven on. The charred connection glowed, so I immediately turned off the oven and the power. I disconnected the bad connector, cut it off from the wire, and stripped the wire to prepare for a new connector, which cost 30 cents at the hardware store. The bake element connection was cleaned, and then the new connector was attached. The power was turned back on, and then the oven was turned on, and it heated perfectly. After confirming several heatings over several hours, the rear panel was reattached, and the oven was pushed back to the wall. This expensive 40" dual fuel oven had been purchased new and used for 3 years by the prior owners of our home. The oven's computer brain died when the oven was 7 years old - the repair cost us $500 for professional labor, parts, and materials. I don't know if I could have done that repair, but I had no intention of shelling that much again, which is why I tried this bake element repair myself. The oven is now 11 years old, and the most likely part to fail is the original bake element. So, we may keep the new part as insurance with the hope of making a fast, easy, inexpensive repair when the original bake element eventually fails.

I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Very simply following the online video instructions.

Replaced element no problem?