All Installation Instructions for LG Refrigerator 78773

water supply to ice maker leaked

Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new

Parts Used:

Plastic Tube - 5/16 Inch

john from locust valley, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The water line was leaking

Removed the damaged tube and replaced the it with a new one.

Parts Used:

Plastic Tube - 5/16 Inch

Awilda from Staten Island, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Pump for ice maker leaked.

Easy repair. Unplugged refer. Took back cover off with screwdriver. Unscrewed the support for the pump. Unhooked water lines from both ends of bad pump. Pulled electrical line off the old pump. Put the support on the new pump, hooked up lines, and electrical plug and screwed the pump to the frame. Put the coever back on unit. Plugged back into wall. Worked immediately.

Parts Used:

Primary Water Valve - Single Coil

Thomas from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Spring was broken on original unit, had to replace whole lever.

removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!

Parts Used:

Refrigerator Lever Spring

Alan from Sun City West, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The ice maker door stay open. And not close back.

So easy that my 13 years old son replaced it.

Parts Used:

SOLENOID ASSEMBLY

Toai from Monroe, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

plastic tube leaking at connector

Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.

Parts Used:

Holder,Bracket

GREG from STILLWATER, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Wrench (Adjustable)

1 of 5 people found this instruction helpful.

Was this instruction helpful to you?

replace hand screw

unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.

Parts Used:

Handle Screw

dorothy from SALISBURY, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Frost in the freezer. Icemaker frozen.

I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.

Parts Used:

Clip

Teresa from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours

1 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Water/ice maker not working

Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.

Parts Used:

Micro Switch

Brent from ROGERS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 34 people found this instruction helpful.

Was this instruction helpful to you?

Plastic door latch/ cam shaft broke on left side door

Removed white plastic trim and installed new latch / cam shaft

Parts Used:

Cam,Shaft

Refrigerator Camshaft

Reginald A. Green from Pelham, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

broken

removed 1 screw and replaced

Parts Used:

Cam,Shaft

Refrigerator Camshaft

william from mashpee, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

icemaker quit working

My husband took out the ice maker. We ordered the part. He looked on YouTube for instructions. Including looking up instructions, I think it took him way less than an hour.

Parts Used:

Ice Maker Assembly

William from Bridge City, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

Was this instruction helpful to you?

Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b

With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Parts Used: