7755 LG Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lights in upper refrigerator would not turn off with doors closed
-
G.J. from WHITE BIRD, ID
- Really Easy
- 15 - 30 mins
-
Screw drivers
replaced melted light covers, replaced switches, and found another problem with power circuit board relay, on order now!!
Other Parts Used:
Was this helpful?
Thank you for voting!
the lights inside the frig weren't shutting off
-
Brian from Troutdale, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
the lights melted the lamp case and cover. I determined it was the switch ,but there was 2 of them . I replaced both . I used a screw driver to pry the covers off the switches which are on the top of the unit .Then I press the tabs on the switch and pulled it out. Slip the wire connect off. slip the wire connect on new switch press it in
... Read more
till the tabs snap in ,put covers back on. the lamp base and cover had two screws holding them, pull the screws slip the old melted base and cover. snap the new base and cover in and put the screws in done!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The tray cover broke, the drawer guide broke
-
Kathy from Boise, ID
- Really Easy
- Less than 15 mins
The repair was easy peasy! Just fit it all in. Shopping here was just as easy. I'd delayed doing it for so long because I thought it'd be laborious but I found my appliance fast and the parts I needed quickly. The diagram you provided with part numbers helped a lot. Thanks for making it easy.
Other Parts Used:
Was this helpful?
Thank you for voting!
Interior Light Would Not Turn Off
-
Thomas from Bay Shore, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install
... Read more
new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.
Read less
Was this helpful?
Thank you for voting!
Plastic door latch/ cam shaft broke on left side door
-
Reginald A. Green from Pelham, AL
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed white plastic trim and installed new latch / cam shaft
Other Parts Used:
Was this helpful?
Thank you for voting!
door mounted cold water tank was leaking at seam of polyethylene tank.
-
RONALD from LAKE WALES, FL
- Very Difficult
- More than 2 hours
-
Screw drivers
The part labeled as water tank was not pictured on web site, and when it arrived it was a large coil of plastic tubing wire-tied in an oval shape,not a blown p/e tank as original.The oval of tubing would not fit into the door compartment, because of the bulk of the actuating solenoid. No instructions were included. It was necessary to ha
... Read more
cksaw the steel solenoid mounting bracket off the solenoid, then contort the solenoid into the compartment to get all parts inside the cover. new connectors had to be purchased, because the the tank/tubing coil was 1/4" od, while the original tank had 5/16"od connections.
Read less
Was this helpful?
Thank you for voting!
Gaskets had to be replaced.
-
Barbara from Palm Beach Gardens, FL
- Really Easy
- 30 - 60 mins
I got my brother to do the repair....lucky me.
Other Parts Used:
Was this helpful?
Thank you for voting!