Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer door gasket needed replacing.
1 personfound this instruction helpful.
Stephen from DICKINSON, TX
Really Easy
Less than 15 mins
Pliers
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this helpful?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
1 personfound this instruction helpful.
Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this helpful?
Thank you for voting!
Replace switch
1 personfound this instruction helpful.
Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers
Read previous tips Taped off area around switch to protect surface Used putty knife to extract switch Used screwdriver to separate connector from switch Plugged in connector Pushed switch assembly into opening Removed tape
Was this helpful?
Thank you for voting!
Wrong parts sent twice. One of the parts was a substitute 2" too long
1 personfound this instruction helpful.
BRENT from RENO, NV
Very Difficult
30 - 60 mins
Unable to complete repair, had to send parts back Part should have been PS11732074, but got PS11732704- wrong part This was a substitute part and was 2" too long
Waiting for refund on this part. It cost me $14.50 to return it by UPS!!!
Was this helpful?
Thank you for voting!
Lights didn't come on when door was opened
1 personfound this instruction helpful.
Philip from Ashland, MA
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this helpful?
Thank you for voting!
Right door cam broken
1 of 2 peoplefound this instruction helpful.
Gary from Goose Creek, SC
Easy
30 - 60 mins
Screw drivers
Remove door seal and cam shaft (one piece). Remove broken cam by removing Philips head screw. Replace broken cam with new cam and reassemble. The actual repair took about 15 minutes however the majority of time was spent figuring out that the door seal and cam shaft had to be removed, no tools required.
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and
... Read morecareful push the switch into the hole until it snaps into place.
Read less
Was this helpful?
Thank you for voting!
old gasket was damaged
1 of 2 peoplefound this instruction helpful.
Maria from TEQUESTA, FL
Really Easy
Less than 15 mins
i removed old and installed new gasket in 5 minutes. i watched a video. it was super easy .
Was this helpful?
Thank you for voting!
Left door when opened the light wouldn’t come on. Checked the light, ok. Ordered push button switch
1 of 2 peoplefound this instruction helpful.
Richard from TULLY, NY
Really Easy
Less than 15 mins
Screw drivers, Wrench (Adjustable)
Removed the cover 2 screws Squeezed the 2 side sleeves and removed Snapped in new button, replaced the cover. Done
Was this helpful?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
1 of 2 peoplefound this instruction helpful.
Alma from Winterport, ME
Very Easy
Less than 15 mins
Screw drivers
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Was this helpful?
Thank you for voting!
Ice buildup in corner of freezer.
1 of 2 peoplefound this instruction helpful.
Louis from BOYNTON BEACH, FL
Really Easy
15 - 30 mins
Screw drivers
Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice
... Read more buildup.
Read less
Was this helpful?
Thank you for voting!
Refrigerator light had a short in it and would randomly work
1 of 3 peoplefound this instruction helpful.
Tammy from HAGERSTOWN, MD
Very Easy
Less than 15 mins
Screw drivers
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Was this helpful?
Thank you for voting!
The water filter needed to be replaced.
1 of 3 peoplefound this instruction helpful.
Alice from Wimberley, TX
Really Easy
Less than 15 mins
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Was this helpful?
Thank you for voting!
After installing the part I found that the ice maker was still not working. I removed the ice maker and found the gears weren't line up.
2 of 6 peoplefound this instruction helpful.
James from LOUISVILLE, KY
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Wrench (Adjustable)
Took old part off and as I removed one hose I put that hose in the corresponding color hole. Then screwed the part on the refrigerator. Water was coming out of the water dispenser fast, but no ice. So I had to continue troubleshooting the ice maker.
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.
My Orders
