7724 (Type 2) Porter Cable Band Saw - Parts

Included in part number 879811

Included in part number 883219

This is a genuine replacement part sourced from the original manufacturer for use with woodworking power tools. The metal screw is used with several different types of equipment, and the application of the screw can vary based on the model of the tool. This screw is available as an individual replacement part, please see model diagram for associative parts.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling ...Read more - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This is an authentic replacement part, sourced from the original manufacturer for use with electric power tools. The special brush holder is used to secure the carbon brushes. This brush holder is available as an individual replacement part, please note two brush holders are required.

This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 7 Feet Long • Porter Cable models: 6302 T4, 6902 T5, T6

This is a Original Manufacturer Sourced replacement part used on some Portable Band Saws. This part is made out of Metal and it is Sold Individually. This roller is essential for guide block that uses rollers to guide the blade, both above and below the table. Included in part number 694978

It is a genuine item which is supplied directly from the original equipment manufacturer for use with Black and Decker, DeWALT and Porter Cable portable band saws. The blade guide holder is secured to the stop assembly, please make sure to check the appropriate diagrams of your model for the correct location and application of this part. ...Read moreIt is made of durable metal and is sold individually, keep in mind the hardware to secure it is sold separately.

Genuine Porter Cable replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can rest...Read moreore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This is a genuine Porter Cable product sourced from the original manufacturer, not an aftermarket imitation. The tube of grease is 5.5 ounces, and is used to lubricate various kinds of equipment, and power tools. This tube of grease is sold individually, please see model diagram for compatibility, and usage.

Includes part number 878725

This replacement screw is a genuine OEM sourced item that is specially made for use with electric power tools. It is a standard hardware which has multiple applications depending on the unit, to ensure correct location and use of this screw check appropriate diagrams of your tool. Note, this hex socket head screw is sold individually.