All Installation Instructions for Range 77-497

Worn Drip Bowls

Pulled out the old drip bowls and replaced with the new. A simple snap!

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

River Oaks Town Homes from DES MOINES, IA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Knobs for the three timers on the appliance console deteriorateddue to age.

The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.

Parts Used:

Clock Knob

Vincent from Bonita Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the burner stop working

Just followed the instructions

Parts Used:

Terminal Block Kit

Anthony J from HAMMONTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Two burners did not heat

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

Parts Used:

Terminal Block Kit

Conan from Moline, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Original terminal degraded and faulty

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Parts Used:

Terminal Block Kit

Robert from PRAIRIEVILLE, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heavy jam boiler caused elements to sag

Removed the old & simply inserted the new one

Parts Used:

Surface Element - 8 Inch - 2600W

Danny L from CHELAN, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Replace Element & Drip Bowl

Just replace the parts. Too easy for an old man.

Parts Used:

Surface Element - 8 Inch - 2600W

Drip Bowl - 8"

Fernando from Orlando, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

8" stove top element would not warm up.

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Parts Used:

Surface Element - 8 Inch - 2600W

Margaret from Spencer, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dead burner

I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.

Parts Used:

Surface Element - 8 Inch - 2600W

Jan from Storm Lake, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

burner was damaged

snap out the old one and snap in the new

Parts Used:

Surface Element - 8 Inch - 2600W

Thomas from Elizabeth City, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Drip bowls needed replacing

Removed the old ones and inserted the new ones.

Parts Used:

Chrome Drip Bowl - 6"

Drip Bowl - 8"

Doris from SUN CITY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The wall oven in our family home since 1963(replaced in the 80’s) wasn’t working. Since I’m the family baker and had returned to live with my sister, it was IMPORTANT/chuckle.

The repair was simple. The part just got plugged in and installed.
Phew, and it works!
I’d found your company when the front burner of the rangetop wasn’t working.
Even though it took awhile to arrive, the wait was kindly explained by a call to customer service. She was very reassuring that it was a back order and they’d let me know when it was shipped. They did, it arrived and I’m very pleased.
Thank you for your excellent service.

Parts Used: