72043 ((ASTCSE2)) LG Refrigerator - Instructions

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.

I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!

Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.

The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!

pried out old switch, disconnected wires ,placed wires on new switch

After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it popped out, you may need to use pliers to disconnect the switch.

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return instructions if y’all still want it back.
Thanks,
Thomas Pennebaker

Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!

Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back into its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!