All Installation Instructions for LG Refrigerator 72033

Leaking

Swapped old one with new one. New one had extra plug not needed.

Parts Used:

Water Inlet Valve Assembly

Johnny from MOUNT OLIVE, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Light switch for refrigerator not functioning

Followed instructions online

Parts Used:

Refrigerator Door Switch

shirley from ONALASKA, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Torn door gasket

Pulled old gasket off by hand. New gasket was easy to install by pushing it into molded cutout in refrigerator door.
Very satisfying to have no glitches in the seamless installation.

Parts Used:

Door Gasket - Gray - Right Side

Tom from BLUFFTON, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Spring broke on Mullion

Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.

Parts Used:

Refrigerator Front Plate Assembly

Michael from MONTGOMERY, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

LED’s we’re not working only 2 we’re lit

Remove 2 screws swing light down a little bit and pull it to front unplug wires . The hard part of job was finding new replacement light, Partselect.com was only sight I could find that had new replacement number and had the light . Other sites including LG site would only tell me the part number on old lights was discontinued 2 of sites said try used appliance dealers

Parts Used:

COVER ASSEMBLY,LAMP

Alan from MADISON, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

rail that holds meat tray broken

remove all trays from refrigerator , remove screw holding rail and install new rail.

Parts Used:

GUIDE ASSEMBLY,RAIL

Steve from GEORGE WEST, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Removed old part.

Installed new one.

Parts Used:

Refrigerator Front Plate Assembly

Steve from NORTH AURORA, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken plastic/glass

Now that you have to buy a complete assembly that includes the drawer in the classy window it's very simple to replace however you buying parts that you don't need simply because G no longer makes the window. Which I find rather odd being as though that they make the whole assembly think and sell windows by themselves for less than 2/3 of what I spent through the whole assembly

Parts Used:

Door Bin Cover

Bill from MURRIETA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

door slight switch failed

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Parts Used:

Refrigerator Door Switch

Greg from CASA GRANDE, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

The switch became intermittent - Possibly a poor designe

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Parts Used:

Refrigerator Door Switch

Sidney from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The spring on the mullion was broken so the mullion would not open to seal the other door.

I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.

Parts Used:

Refrigerator Front Plate Assembly

JANET from GRAND JCT, CO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs on the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

Parts Used:

Refrigerator Door Switch

JON from OJAI, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken freezer rail.

Took out tray , removed 2 screws, removed old rail and installed new one.

Parts Used:

ELECTRIC PARTS ASSEM

John from STEPHENVILLE, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken spring on flapper door

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

Parts Used:

Refrigerator Front Plate Assembly